Endress+Hauser HART Proline t-mass I 300 Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 202

background image

Proline t-mass I 300 HART

Diagnostics and troubleshooting

Hauser

145

Available status signals

Configuration as per HART 7 Specification (Condensed Status), in accordance with

NAMUR NE107.

Symbol

Meaning

A0013956

Failure

A device error is present. The measured value is no longer valid.

A0013959

Function check

The device is in service mode (e.g. during a simulation).

A0013958

Out of specification

The device is being operated:
• Outside its technical specification limits (e.g. outside the process temperature range)
• Outside of the configuration carried out by the user (e.g. maximum flow in parameter

20 mA value

)

A0013957

Maintenance required

Maintenance is required. The measured value is still valid.

A0023076

Has no effect on the condensed status.

11.7 Overview of diagnostic information

The amount of diagnostic information and the number of measured variables affected

increase if the measuring device has one or more application packages.
In the case of some items of diagnostic information, the status signal and the

diagnostic behavior can be changed. Change the diagnostic information →  144

Diagnostic

number

Short text

Remedy instructions

Status

signal

[from the

factory]

Diagnostic

behavior

[from the

factory]

Diagnostic of sensor

004

Sensor error

Change sensor

F

Alarm

082

Data storage

1. Check module connections
2. Change electronic modules

F

Alarm

083

Memory content

1. Restart device
2. Restore HistoROM S-DAT backup

('Device reset' parameter)

3. Replace HistoROM S-DAT

F

Alarm

144

Sensor drift

1. Check sensor
2. Replace sensor

F

Alarm

Diagnostic of electronic

201

Device failure

Restart device

F

Alarm

242

Software incompatible

1. Check software
2. Flash or change main electronics

module

F

Alarm

252

Modules incompatible

1. Check electronic modules
2. Check if correct modules are

available (e.g. NEx, Ex)

3. Replace electronic modules

F

Alarm

252

Modules incompatible

1. Check if correct electronic modul

is plugged

2. Replace electronic module

F

Alarm

«
...
143
144
145
146
147
...
»

Содержание HART Proline t-mass I 300











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HART Proline t-mass I 300

PLATINUM Series

Бренд: Hach Страницы: 64

Бренд: horiba Страницы: 27

Бренд: Palstar Страницы: 37

Бренд: LD Didactic Страницы: 2

Бренд: UEi Страницы: 5

Orion Versa Star Pro Series

Бренд: Thermo Scientific Страницы: 4

Бренд: Osaka Страницы: 3

Бренд: SIKA Страницы: 8

Бренд: Keysight Technologies Страницы: 10

Бренд: AccuEnergy Страницы: 23

In-Situ Rugged TROLL 100

Бренд: Geotech Страницы: 6

Everywhereyoulook Frontline X500

Бренд: Teledyne Lecroy Страницы: 8

Бренд: xDEEP Страницы: 57

Бренд: BorMann Страницы: 8

Бренд: Kane Страницы: 46

Бренд: Alstom Страницы: 154

Бренд: BINMASTER Страницы: 20

Бренд: PCE Instruments Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды