Endress+Hauser HART Proline Promass 83 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 148

background image

Proline Promass 83

Operation

Hauser

49

5.4.5

Device status / Error messages

You can read the extended device status, in this case, current error messages, via Command
"48". The command delivers information which are partly coded in bits (see table below).

!

Note!
Explanation of the device status and error messages and their elimination ® Page 84 ff.

HART 5

Byte-bit

Error No.

Short error description

0-0

001

Serious device error

0-1

011

Measuring amplifier has faulty EEPROM

0-2

012

Error when accessing data of the measuring amplifier EEPROM

1-1

031

S-DAT: Defective or missing

1-2

032

S-DAT: Error accessing saved values

1-3

041

T-DAT: Defective or missing

1-4

042

T-DAT: Error accessing saved values

1-5

051

I/O board and the amplifier board are not compatible.

3-3

111

Totalizer checksum error

3-4

121

I/O board and the amplifier board (software versions) are not compatible.

3-6

205

T-DAT: Data download not successful

3-7

206

T-DAT: Data upload not successful

4-3

251

Internal communication fault on the amplifier board.

4-4

261

No data reception between amplifier and I/O board

5-7

339

Flow buffer:
The temporarily buffered flow portions (measuring mode for pulsating
flow) could not be cleared or output within 60 seconds.

6-0

340

6-1

341

6-2

342

6-3

343

Frequency buffer:
The temporarily buffered flow portions (measuring mode for pulsating
flow) could not be cleared or output within 60 seconds.

6-4

344

6-5

345

6-6

346

6-7

347

Pulse buffer:
The temporarily buffered flow portions (measuring mode for pulsating
flow) could not be cleared or output within 60 seconds.

7-0

348

7-1

349

7-2

350

7-3

351

Current output:
The actual value for the flow lies outside the set limits.

7-4

352

7-5

353

7-6

354

7-7

355

Frequency output:
The actual value for the flow lies outside the set limits.

8-0

356

8-1

357

8-2

358

«
...
47
48
49
50
51
...
»

Содержание HART Proline Promass 83





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HART Proline Promass 83

Бренд: AccuMASTER Страницы: 2

Бренд: Banner Страницы: 11

Бренд: Bante Instruments Страницы: 10

Бренд: BANTE Страницы: 11

Бренд: Banner Страницы: 14

Бренд: Banner Страницы: 16

Бренд: Roland Страницы: 15

Бренд: M-system Страницы: 13

Бренд: MadMan Страницы: 37

Бренд: MADDALENA Страницы: 5

Бренд: WATERGUARD Страницы: 2

Бренд: Daewoo Страницы: 17

Бренд: Valcom Страницы: 1

Бренд: Keller Страницы: 4

Бренд: odoland Страницы: 6

UNITY INOVA NMR

Бренд: Varian Страницы: 65

Бренд: Roland Страницы: 224

Бренд: Fungilab Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды