Endress+Hauser Hart Micropilot FMR60B Скачать руководство пользователя страница 22

Страница: 22 / 84

Electrical connection

Micropilot FMR60B HART

Hauser

Electrical connection

6.1

Connecting requirements

6.1.1

Cover with securing screw

In the case of devices for use in the hazardous area with a certain type of protection, the

cover is sealed by a securing screw.

NOTICE

If the securing screw is not positioned correctly, the cover cannot provide secure

sealing.

‣

Open the cover: slacken the screw of the cover lock with a maximum of 2 turns so that

the screw does not fall out. Fit the cover and check the cover seal.

‣

Close the cover: screw the cover securely onto the housing, making sure that the

securing screw is positioned correctly. There should not be any gap between the cover

and housing.

2 x

0.7 Nm

A0039520

 2

Cover with securing screw

6.1.2

Potential equalization

The protective ground on the device must not be connected. If necessary, the potential

matching line can be connected to the outer ground terminal of the transmitter before the

device is connected.

A0046583

Single compartment housing, plastic

Single compartment housing, aluminum

Dual compartment housing

Dual compartment housing, L-form

Ground terminal for connecting the potential matching line

WARNING

Explosion Hazard!

‣

Please refer to the separate documentation on applications in hazardous areas for the

safety instructions.

For optimum electromagnetic compatibility:

• Keep the potential matching line as short as possible

• Observe a cross-section of at least 2.5 mm

(14 AWG)

Содержание Hart Micropilot FMR60B





















































































Результаты поиска

Содержание Hart Micropilot FMR60B

Отзывы:

Похожие инструкции для Hart Micropilot FMR60B

Бренды по названию

Популярные бренды

Endress+Hauser Hart Micropilot FMR60B, Руководство по эксплуатации

Результаты поиска

Содержание Hart Micropilot FMR60B

Отзывы:

Похожие инструкции для Hart Micropilot FMR60B

Бренды по названию

Популярные бренды