Endress+Hauser Dosimag Скачать руководство пользователя страница 34

Страница: 34 / 76

Commissioning

Dosimag

Hauser

10.4.3 Configuring the pulse/frequency/switch output

The

Pulse/frequency/switch output 1 to 2

submenu contains all the parameters that

must be configured for the configuration of the selected output type.

Configuring the pulse output

In the

Operating mode

parameter (→  34), one of the two options can be selected for

the pulse output:

•

Pulse

option: Quantity-proportional pulse with pulse width to be configured.

•

Automatic pulse

option: Quantity-proportional pulse with on/off ratio of 1:1

Navigation

"Setup" menu → Pulse/frequency/switch output 1 to 2

Structure of submenu for pulse output

‣

Pulse/frequency/switch output 1
to 2

Operating mode

Channel 2

Assign pulse output

Value per pulse

Pulse width

Failure mode

Invert output signal

Parameter overview with brief description

Parameter

Prerequsite

Description

Selection / User

entry

Factory setting

Operating mode

–

Define the output as a pulse,
frequency or switch output.

• Off
• Pulse
• Automatic pulse
• Frequency
• Switch

•

Pulse/frequency/
switch output 1

submenu:

Pulse

option

•

Pulse/frequency/
switch output 1 to
2

submenu:

Switch

option

Channel 2

The

Pulse

option is selected in

the

Operating mode

parameter.

Select impulse with or without
time offset.

• Off
• Redundant 0°
• Redundant 90°
• Redundant 180°

Off

Assign pulse output

One of the following options is
selected in the

Operating

mode

parameter:

• Pulse
• Automatic pulse

Select process variable for
pulse output.

• Off
• Volume flow

Off

Содержание Dosimag













































































Результаты поиска

Содержание Dosimag

Отзывы:

Похожие инструкции для Dosimag

Бренды по названию

Популярные бренды

Endress+Hauser Dosimag, Руководство по эксплуатации

Результаты поиска

Содержание Dosimag

Отзывы:

Похожие инструкции для Dosimag

Бренды по названию

Популярные бренды