Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

61

EMPTY CALIB. (010)
Entry

Enter level, volume, mass or percentage value for the lower calibration point (container
empty).
The values entered for the EMPTY CALIB. and EMPTY PRESSURE parameters form the
pressure-level value pair for the lower calibration point. The unit is selected via the
OUTPUT UNIT parameter (



Page 60).

Prerequisite:

• CALIBRATION MODE = Dry

Factory setting:

0.0

EMPTY PRESSURE (011)
Entry

Enter pressure value for the lower calibration point (container empty).



See also EMPTY CALIB.

Prerequisite:

• CALIBRATION MODE = Dry

Factory setting:

0.0

FULL CALIB. (004)
Entry

Enter height, volume, mass or percentage value for the upper calibration point (container
full).
The values entered for the FULL CALIB. and FULL PRESSURE parameters form the
pressure-level value pair for the upper calibration point. The unit is selected via the
OUTPUT UNIT parameter (



Page 60).

Prerequisite:

• CALIBRATION MODE = Dry

Factory setting:

100.0

FULL PRESSURE (005)
Entry

Enter pressure value for the upper calibration point (container full).



See also FULL CALIB.

Prerequisite:

• CALIBRATION MODE = Dry

Factory setting:

100.0

SET LRV (013)
Entry

Enter value for the lower current value (4 mA). The unit is selected via the OUTPUT
UNIT parameter (



Factory setting:

0.0

SET URV (012)
Entry

Enter value for the upper current value (20 mA). The unit is selected via the OUTPUT
UNIT parameter (



Factory setting:

100.0

DAMPING VALUE (247)
Entry

Enter damping time (time constant



).

The damping affects the speed at which all subsequent elements, such as the on-site
display, measured value and current output react to a change in the pressure.

Input range:

0.0 to 999.0 s

Factory setting:

2.0 s or as per order specifications

Table 8: (GROUP SELECTION



) OPERATING MENU



SETTINGS



BASIC SETUP "Level",

LEVEL SELECTION "Level Easy Pressure"

«
...
59
60
61
62
63
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Бренд: Nauticam Страницы: 2

Бренд: Campbell Страницы: 70

Бренд: Yuasa Страницы: 35

Бренд: 3M Страницы: 10

21 COVERT Series

Бренд: Code 3 Страницы: 16

Classic Studex Mk2 G1326 G1326

Бренд: Gitzo Страницы: 1

TABFZ-G1-HS1117

Бренд: Tablet EX Gear Страницы: 2

RevitaSpa RS-L305A

Бренд: Air innovations Страницы: 12

Бренд: Lexicon Страницы: 14

Бренд: V-TAC Страницы: 136

Бренд: Bioenno Power Страницы: 2

Бренд: Lafferty Страницы: 4

Бренд: A&D Страницы: 68

Бренд: Happy Trails Страницы: 3

Бренд: MAXWORKS Страницы: 7

Бренд: R&G Страницы: 15

Бренд: Yeti Страницы: 13

echoflex OWS-DT-UW-120/277

Бренд: ETC Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды