Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

53

P01-xxxxxxxx-19-xx-xx-xx-083

Fig. 26:

POSITION ADJUSTMENT function group

MAX PRESS. FLOW (634)
Entry

Enter maximum pressure of primary element.



See layout sheet of primary element. This value is assigned to the maximum flow value

(



see MAX. FLOW).

!

Note!

Use the LINEAR/SQROOT parameter (



Page 113) to specify the current signal for the

"Flow" measuring mode. The following applies for the "Differential pres." setting:
If you enter a new value for MAX PRESS. FLOW, the value for SET URV is also changed.
Use SET URV to assign a pressure value to the upper current value. If you want to assign
the upper current value a value other than that for MAX PRESS. FLOW, you must enter
the desired value for SET URV. (



SET URV, Page 100).

Factory setting:

High sensor limit (



See PRESS. SENS HILIM, Page 119)

DAMPING VALUE (247)
Entry

Enter damping time (time constant



).

The damping affects the speed at which all subsequent elements, such as the on-site
display, measured value and current output react to a change in the pressure.

Input range:

0.0...999.0 s

Factory setting:

2.0 s or as per order specifications

Table 5: (GROUP SELECTION



) QUICK SETUP "Flow"

Parameter name

Description

1)

1)

LANGUAGE

BASIC SETUP

DISPLAY

SETTINGS

POSITION ADJUSTMENT

OPERATING MENU

GROUP SELECTION

Measured value

EXTENDED SETUP

CALIB. OFFSET

POS. ZERO ADJUST

POS. INPUT VALUE

1) Display via

on-site display only

Table 6: (GROUP SELECTION



)



OPERATING MENU



SETTINGS



POSITION ADJUSTMENT

Parameter name

Description

Due to the orientation of the device, there may be a shift in the measured value, i.e. when the container is empty or partly
filled, the measured value does not display zero. Deltabar S and Cerabar S offer three different ways of performing a
position adjustment.

Recommendation:
• The pressure difference between zero (set point) and the measured pressure need not be known.

– POS. ZERO ADJUST: Deltabar S or Cerabar S with gauge pressure sensor or Deltapilot S.
– POS. INPUT VALUE: Cerabar S with absolute pressure sensor.

• The pressure difference between zero (set point) and the measured pressure is known.

– CALIB. OFFSET: Deltabar S, Cerabar S with gauge pressure sensor, Cerabar S with absolute pressure sensor or

Deltapilot S.

«
...
51
52
53
54
55
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Бренд: Samsung Страницы: 2

Бренд: Jabra Страницы: 2

SP200 - QUICKSTART GUIDE 1

Бренд: Jabra Страницы: 2

JABRA FREEWAY HFS100

Бренд: Jabra Страницы: 40

BT150 - Headset - Over-the-ear

Бренд: Jabra Страницы: 2

Бренд: Omnicomm Страницы: 20

Бренд: omnicharge Страницы: 12

Бренд: Saab Страницы: 10

AERASGARD RCO2-W

Бренд: S+S Regeltechnik Страницы: 7

Бренд: Metric Halo Страницы: 21

KARLSUDD TRAVEL BED

Бренд: Carena Страницы: 8

Бренд: Omron Страницы: 2

Бренд: Naish Страницы: 23

FIX&GO automatic

Бренд: Alfa Romeo Страницы: 40

Бренд: Kargo Master Страницы: 6

CombiCool CAB-40B

Бренд: Waeco Страницы: 136

Бренд: CASTLECREEK Страницы: 3

Бренд: Inateck Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды