Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 156

background image

Description of parameters

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

100

Hauser

P01-xxxxxxxx-19-xx-xx-xx-091

Fig. 38:

LINEARISATION function group for on-site operation

SET URV (638)
Entry

Depending on the setting in the LINEAR/SQROOT parameter (



Page 113), enter a flow

value or a pressure value for the upper current value (20 mA) here.

• LINEAR/SQROOT = Flow (square root) (factory setting)



flow value

• LINEAR/SQROOT = Differential pres.



pressure value

The following applies for the setting LINEAR/SQROOT "Flow (square root)":
• If you enter a new value for MAX. FLOW, the value for SET URV is also changed. If

you want to assign the upper current value a value other than that for MAX. FLOW,
you must enter the desired value for SET URV. (



MAX. FLOW, Page 95).

The following applies for the setting LINEAR/SQROOT "Differential pres.":
• If you enter a new value for MAX PRESS. FLOW, the SET URV value is also changed. If

you want to assign the upper current value a value other than that for MAX PRESS.
FLOW, you must enter the desired value for SET URV. (



MAX PRESS. FLOW,

Page 95).

Factory setting:

MAX. FLOW

Table 17: (GROUP SELECTION



) OPERATING MENU



SETTINGS



EXTENDED SETUP "Flow"

Parameter name

Description

1)

1)

EDITOR TABLE

EDITOR TABLE

MEASURING TABLE

Editor Table

Measuring Table

EDITOR TABLE

TANK CONTENT MIN

LIN. EDIT MODE

TANK DESCRIBTION

TANK CONTENT MAX

TABLE SELECTION

MEASURING TABLE

LANGUAGE

DISPLAY

SETTINGS

POSITION ADJUSTMENT

OPERATING MENU

GROUP SELECTION

Measured value

LINEARIZATION

Level measuring
mode only

1) Display via on-site display only

Table 18: (GROUP SELECTION



) OPERATING MENU



SETTINGS



LINEARISATION

– on-site operation

Parameter name

Description

Prerequisite

:

• MEASURING MODE = Level (



see also Page 45).

• LEVEL MODE = Pressure Linearized or Height Linearized (



see also Page 68).

Note:

– See also Page 14 ff, Section 5 "Level measurement".

«
...
98
99
100
101
102
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Бренд: IHP Страницы: 8

Бренд: Cane Creek Страницы: 2

Бренд: Labona Страницы: 12

Бренд: Öhlins Страницы: 2

Soft Luggage Pannier Racks

Бренд: Honda Страницы: 10

Бренд: Paxton Automotive Страницы: 85

Бренд: Thule Страницы: 8

Бренд: BAFANG Страницы: 12

Бренд: Trailboss Страницы: 5

Бренд: Jula Страницы: 5

OADR 20I6465/S14F

Бренд: Baumer Страницы: 4

Бренд: Omron Страницы: 2

Бренд: IBASE Technology Страницы: 100

Бренд: JUGS Страницы: 17

Бренд: LEGRAND Страницы: 2

S2000 Windscreen Camera Mount

Бренд: Modifry Products Страницы: 2

Бренд: Montgomery Ward Страницы: 4

Бренд: Logitech Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды