Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

129

ACK. ALARM (500)
Selection

Acknowledge alarm.

Prerequisite:

• ACK. ALARM MODE = on

Options:

• Abort
• Confirm

The cause of the alarm must be eliminated, the message must be acknowledged via the
ACK. ALARM parameter and, where applicable, the ALARM DISPL. TIME (



Page 129)

has to have elapsed before the device starts measuring again following an alarm.



See also these Operating Instructions, Section 8.3 "Confirming messages".

Factory setting:

Abort

RESET ALL ALARMS (603)
Selection

Use this parameter to reset all the messages of the LAST DIAG. CODE parameter.

Options:

• Abort
• Confirm

Factory setting:

Abort

ERROR No.
Entry

For "Error"-type messages, you can decide whether the device should behave as in the
event of an alarm (A) or as in the event of a warning (W). Enter the corresponding
message number for this parameter.



See also SELECT ALARMTYPE.



See also these Operating Instructions, Section 8.1 "Messages" and Section 8.2

"Response of outputs to errors".

Prerequisite:

• Digital communication

SELECT ALARMTYPE
(595) – Entry
(600) – Selection

For "Error"-type messages, you can decide whether the device should behave as in the
event of an alarm (A) or as in the event of a warning (W).



See also ERROR No.



See also these Operating Instructions, Section 8.2 "Response of outputs to errors".

Options

:

• Alarm (A): output current assumes a defined value.
• Warning (W): device continues measuring

On-site operation:

1.

Enter the corresponding message number for ERROR No. field.

2.

Select "Alarm" or "Warning" option.

Digital communication:

1.

Enter the corresponding message number via the ERROR No. parameter.

2.

Use the SELECT ALARMTYPE parameter to select the "Alarm" or "Warning" option.

ALARM DELAY (336)
Entry

Enter alarm response time for all "Error" messages.

!

Note!

There is no alarm if the cause of the error is eliminated within the alarm delay time.

Input range:

0...100 s

Factory setting:

0.0 s

ALARM DISPL. TIME (480)
Entry

Enter alarm display time for all "Error" messages. Once the cause of the error is rectified,
the alarm display time starts running.

!

Note!

The following applies if the setting for ACK. ALARM MODE = on:
If an alarm appears and the alarm display time elapses before the alarm has been
acknowledged, the message will be cleared once it has been acknowledged.



See also these Operating Instructions, Section 8.3 "Confirming messages".

Input range:

0...999.9 s

Factory setting:

0.0 s

Table 33: (GROUP SELECTION



) OPERATING MENU



DIAGNOSTICS



MESSAGES

Parameter name

Description

«
...
127
128
129
130
131
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Бренд: NEC Страницы: 144

Бренд: Bang & Olufsen Страницы: 12

Бренд: A&D Страницы: 35

Бренд: Hanlong Страницы: 26

Бренд: Labelmate Страницы: 2

Бренд: Labnet Страницы: 2

Бренд: Harol Страницы: 17

Бренд: Cab Technology Страницы: 10

Бренд: Harol Страницы: 16

Energi Savr Node QSN-4S16-S

Бренд: Lutron Electronics Страницы: 12

HookUpz Smartphone Telescope Adapter

Бренд: Carson Страницы: 16

Бренд: Masterack Страницы: 4

Бренд: Over Armour Offroad Страницы: 5

Бренд: ECG Страницы: 24

Бренд: Compass Страницы: 16

Бренд: J And N Страницы: 12

Бренд: Whispbar Страницы: 14

Бренд: FDC Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды