Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 156

background image

Pressure measurement

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

12

Hauser

!

Note!
• You can also specify a customer-specific unit. See parameter description for PRESS. ENG. UNIT

(



4.2

Calibration without reference pressure

Example:

In this example, a device with a 400 mbar (6 psi) sensor is configured for the 0...+300 mbar (4.5
psi) measuring range, i.e. 0 mbar and 300 mbar (4.5 psi) are assigned to the 4 mA value and 20 mA
value respectively.

Prerequisite:

• This is a theoretical calibration, i.e. the pressure values for the

lower range and upper range value are known.

Description

1

Deltabar S: before configuring the device for your
application, the pressure piping must be cleaned and
filled with fluid. See Operating Instructions BA00270P,
Section 6.6.

P01-PMD75xxx-19-xx-xx-xx-000

P01-xxxxxxxx-05-xx-xx-xx-010

Fig. 1:

Calibration with reference pressure

1

See table, step 6.

2

See table, step 7.

2

Carry out position adjustment if necessary. See Page 53,
Table 6: POSITION ADJUSTMENT.

3

If necessary, select the "Pressure" measuring mode via
the MEASURING MODE parameter.

On-site display:
Menu path: GROUP SELECTION



MEASURING

MODE

Digital communication:
Menu path:



OPERATING MENU



SETTINGS



BASIC SETUP



MEASURING MODE

4

On-site display:
Select BASIC SETUP function group.
Menu path: GROUP SELECTION



OPERATING

MENU



SETTINGS



BASIC SETUP

5

Select a pressure unit via the PRESS. ENG. UNIT
parameter, here mbar for example.

6

The pressure for the lower range value (4 mA value) is
present at the device, here 0 mbar for example.

Select GET LRV parameter.

Confirm value present. The pressure value present is
assigned to the lower current value (4 mA).

7

The pressure for the upper range value (20 mA value) is
present at the device, here 300 mbar (4.5 psi) for
example.

Select GET URV parameter.

Confirm value present. The pressure value present is
assigned to the upper current value (20 mA).

8

Result:
The measuring range is set for 0...+300 mbar (4.5 psi).

+

–

20

4

I

[mA]

0

300

p

[mbar]

➀

➁

«
...
10
11
12
13
14
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Бренд: Walimex Pro Страницы: 4

BIESEMEYER 78-955

Бренд: Delta Страницы: 12

Бренд: ICC Страницы: 32

Бренд: Öhlins Страницы: 8

prodrive SUR 3A00

Бренд: Öhlins Страницы: 4

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 8

Бренд: Öhlins Страницы: 4

Бренд: Snapper Страницы: 1

Бренд: Whispbar Страницы: 16

Бренд: Valor Fires Страницы: 12

7 34970 00351 7

Бренд: Primo Water Страницы: 12

Бренд: media-tech Страницы: 13

Бренд: matev Страницы: 23

Бренд: Axxess Страницы: 8

Бренд: Ikelite Страницы: 32

Бренд: Deka Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды