Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

117

CUST. TAG NUMBER (055)
Entry

Enter TAG number (max. 8 alphanumeric characters).

Factory setting:

_ _ _ _ _ _ _ _ or as per order specifications

LONG TAG NUMBER (305)
Entry

Enter TAG number (max. 32 alphanumeric characters).

Factory setting:

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
or as per order specifications

ADDITIONAL INFO. (272)
Entry

Enter tag description (max. 16 alphanumeric characters).

Factory setting:

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ or as per order specifications

DEVICE DESIGN. (350)
Display

Displays the device designation and order code.

HARDWARE REV. (266)
Display

Displays the revision number of the main electronics
e.g.: V02.00

SOFTWARE VERSION (264)
Display

Displays the software version
e.g.: V02.10

CONFIG RECORDER (352)
Display

Displays the configuration counter.
This counter is increased by one with each change to a parameter or group. The counter
counts to 65535 and then starts again at zero. Changes in the parameters of the DISPLAY
function group do not increase the counter.

PCB TEMPERATURE (357)
Display

Displays the measured temperature of the main electronics.

ALLOWED MIN. TEMP
(358)
Display

Displays the lower temperature limit of the main electronics.

ALLOWED MAX. TEMP
(359)
Display

Displays the upper temperature limit of the main electronics.

DIP STATUS (363)
Display

Displays the status of DIP switch 1 on the electronic insert.
You can lock or unlock parameters relevant to the measured value with DIP switch 1. If
operation is locked by means of the INSERT PIN No. parameter, you can only unlock
operation again by means of this parameter. (



INSERT PIN NO, see Page 126.)



See also Operating Instructions BA00270P (Deltabar S), BA00271P (Cerabar S) or

BA00332P (Deltapilot S), Section 5.9 "Locking/unlocking operation".

Display:

• On (locking switched on)
• Off (locking switched off)

Factory setting:

Off (locking switched off)

Table 25: (GROUP SELECTION



) OPERATING MENU



TRANSMITTER INFO



PROCESS

CONNECTION

Parameter name

Description

Pmax PROC. CONN. (570)
Entry

For entering and displaying the maximum permitted pressure of the process connection.

Factory setting:

In accordance with nameplate data (



see also Operating Instructions BA00270P

(Deltabar S), BA00271P (Cerabar S) or BA00332P (Deltapilot S), Section 2.1.1
nameplate)

Table 24: (GROUP SELECTION



) OPERATING MENU



TRANSMITTER INFO



TRANSMITTER DATA

Parameter name

Description

«
...
115
116
117
118
119
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Бренд: Unex Страницы: 24

Бренд: Barco Страницы: 2

Бренд: DBI SALA Страницы: 32

Бренд: Hach Страницы: 148

Бренд: Omega Engineering Страницы: 2

Бренд: Oki Страницы: 52

Бренд: U-Line Страницы: 3

Бренд: PCB Piezotronics Страницы: 15

Бренд: Stobag Страницы: 3

PowerPack TPB-2112

Бренд: texet Страницы: 16

Бренд: Graphite Страницы: 44

Бренд: amora Страницы: 84

Бренд: FormFit Страницы: 4

Бренд: Homelite Страницы: 1

Бренд: Acuity Brands Страницы: 3

AAB-P-RZR900-K2-001

Бренд: SuperATV Страницы: 3

Бренд: Omega Engineering Страницы: 13

Бренд: Gardena Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды