Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 156

background image

Description of parameters

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

126

Hauser

Table 31: (GROUP SELECTION



) OPERATING MENU



OPERATING

Parameter name

Description

ENTER RESET CODE (047)
Entry

Reset parameters completely or partially to factory values or delivery status.



See also Operating Instructions BA00270P (Deltabar S), BA00271P (Cerabar S) or

BA00332P (Deltapilot S), Section 5.10 "Factory setting" (reset).

Factory setting:

0

OPERATING HOURS (409)
Display

Displays the hours of operation. This parameter cannot be reset.

INSERT PIN NO (048)
Entry

For entering a code to lock or unlock operation.

!

Note!

• The

-symbol on the on-site display indicates that operation is locked. Parameters

which refer to how the display appears, e.g. LANGUAGE and DISPLAY CONTRAST
can still be altered.

• If operation is locked by means of the DIP-switch, you can only unlock operation again

by means of the DIP-switch. If operation is locked by means of the on-site display or
remote operation e.g. FieldCare, you can unlock operation again by means of the on-
site display or using remote operation.



See also Operating Instructions BA00270P (Deltabar S), BA00271P (Cerabar S) or

BA00332P (Deltapilot S), Section 5.9 "Locking/unlocking operation".

Options:

• Lock: enter a number between 0...9999 which is



100.

• Unlock: enter the number 100.

Factory setting:

100

HistoROM AVAIL. (831)
Display

Indicates whether the optional HistoROM®/M-DAT memory module is connected to the
electronic insert.



See also Operating Instructions BA00270P (Deltabar S), BA00271P (Cerabar S) or

BA00332P (Deltapilot S), Section 5.5 "HistoROM

®

/M-DAT (optional)".

Options:

• Yes (HistoROM

®

/M-DAT is attached to the electronic insert)

• No (HistoROM

®

/M-DAT is not attached to the electronic insert)

DOWNLOAD SELECT (014)
Options

Select download function from HistoROM to device. The selection has no effect on an
upload from the device to the HistoROM.

Prerequisite:

• A HistoROM

®

/M-DAT is attached to the electronic insert

(HistoROM AVAIL. = yes)

Options:

• Configuration copy: For this option, all parameters apart from the DEVICE SERIAL No,

DEVICE DESIGN., CUST. TAG NUMBER, LONG TAG NUMBER, ADDITIONAL
INFO., BUS ADDRESS, CURRENT MODE and the parameters of the POSITION
ADJUSTMENT and PROCESS CONNECTION group are overwritten.

• Device replacement: With this option, all parameters except for DEVICE SERIAL No,

DEVICE DESIGN. and the parameters of the POSITION ADJUSTMENT and PROCESS
CONNECTION group are overwritten.

• Electronics replace: With this option, all parameters except for the parameters of the

POSITION ADJUSTMENT group are overwritten.

Factory setting:

Copy config. (if HistoROM

®

/M-DAT is attached to the electronic insert)

«
...
124
125
126
127
128
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Бренд: PASCO Страницы: 5

Бренд: PASCO Страницы: 4

Бренд: PASCO Страницы: 8

Бренд: PASCO Страницы: 4

Бренд: PASCO Страницы: 12

Бренд: PASCO Страницы: 5

Бренд: PASCO Страницы: 3

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

Бренд: probrake Страницы: 2

Бренд: Pitney Bowes Страницы: 22

IO-Link BAE SA-CS-027-YI-BP00,3 GS04

Бренд: Balluff Страницы: 50

Бренд: Cobra Страницы: 2

Sagewash Sanitizer

Бренд: Sage Страницы: 2

Бренд: Recsea Страницы: 9

Бренд: R&G Страницы: 4

Бренд: Bison Страницы: 3

Бренд: Thule Страницы: 8

Бренд: Ultrak Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды