Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 156

background image

Description of parameters

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

108

Hauser

TOTALIZER 1 UNIT
(398), (666), (664), (662)
Selection

Select unit for totalizer 1.
Depending on the setting in the FLOW-MEAS. TYPE parameter (



Page 93) this

parameter offers a list of volume, norm volume, standard volume and mass units. When a
new volume or mass unit is selected, totalizer-specific parameters are converted and
displayed with the new unit within a unit group. When the flow mode is changed, the
totalizer value is not converted.

The 3-digit ID number on the on-site display depends on the FLOW-MEAS. TYPE
selected:
– (398): FLOW-MEAS. TYPE "Volume p. cond."
– (662): FLOW-MEAS. TYPE "Mass"
– (664): FLOW-MEAS. TYPE "Gas. std. cond."
– (666): FLOW-MEAS. TYPE "Gas. norm conditions"

Factory setting:

m

3

TOT. 1 USER UNIT (627)
Entry

Enter text (unit) for customer-specific unit for totalizer 1.
You can enter a maximum of eight alphanumeric characters here.



See also FACT. U.

U. TOTAL. 1.

Prerequisite:

• TOTALIZER 1 UNIT = User unit

!

Note!

Only the first five characters are shown on the on-site display. For example, if "crates" is
specified as the customer-specific unit, "crate" is displayed.
If the unit contains a slash, up to eight characters can be shown on the on-site display.
The maximum number of characters in the counter is again limited to five. For example,
if "crates/m2" is specified as the customer-specific unit, "crate/m2" is displayed. In the
FieldCare, all eight characters are displayed.
In the HART handheld terminal, the customer-specific unit is only displayed in the TOT.
1 USER UNIT parameter. The measured value is displayed with the additional text "User
Unit".

Factory setting:

_ _ _ _ _ _ _ _

FACT. U. U. TOTAL. 1 (329)
Entry

Enter conversion factor for a customer-specific unit for totalizer 1.
The conversion factor must be entered in relation to an appropriate SI unit, e.g. m

3

for the

"Volume p. cond." FLOW-MEAS. TYPE.



See also TOT. 1 USER UNIT.

Prerequisite:

• TOTALIZER 1 UNIT = User unit

Example:

You want the measured value to be displayed in "buckets".

– MEASURED VALUE =1 m3

i

100 buckets

– Entry TOT. 1 USER UNIT: bucket
– Entry FACT. U. U. TOTAL. 1: 100
– Result: MEASURED VALUE = 100 buckets

Factory setting:

1.0

NEG. FLOW TOT. 1 (400)
Selection

Specify way of counting negative flows for totalizer 1.

P01-xMD7xxxx-16-xx-xx-xx-003

Factory setting:

Inc. on neg. flow

Table 20: (GROUP SELECTION



)



OPERATING MENU



SETTINGS



TOTALIZER SETUP

Parameter name

Description

Options

Stop on neg. flow

Dec. on neg. flow

Inc. on. neg. flow

negative flow

Total remains constant

Total decreases

Total increases

Total increases

Total increases

Total increases

positive flow

«
...
106
107
108
109
110
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Бренд: Canon Страницы: 115

Toughbook CF-F8EWDZZAM

Бренд: Panasonic Страницы: 20

Бренд: Campbell Страницы: 64

Бренд: Campbell Страницы: 42

Бренд: Campbell Страницы: 19

Бренд: Campbell Страницы: 26

Бренд: Campbell Страницы: 19

Бренд: Campbell Страницы: 27

Бренд: Raven Страницы: 24

Бренд: Campbell Страницы: 14

Бренд: Campbell Страницы: 2

TEMPERATURE PROBE 109SS

Бренд: Campbell Страницы: 18

Бренд: Campbell Страницы: 77

Бренд: Campbell Страницы: 30

Бренд: Weather Guard Страницы: 4

Бренд: Campbell Страницы: 2

Бренд: Xerox Страницы: 13

Бренд: Xerox Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды