Endress+Hauser Deltabar S FMD77 Скачать руководство пользователя страница 62

Страница: 62 / 114

Commissioning

Deltabar S FMD77, FMD78, PMD75 with FOUNDATION Fieldbus

Hauser

Commissioning

The device is configured for the Pressure measuring mode as standard. The measuring range

and the unit in which the measured value is transmitted correspond to the specifications on

the nameplate.

WARNING

Exceeding the maximum allowable working pressure!

Risk of injury due to bursting of parts! Warning messages are generated if pressure is too

high.

‣

If a pressure greater than the maximum permitted pressure is present at the device, the

messages "E115 Sensor overpressure" and "E727 Sensor pressure error - overrange" are

output in succession! Use the device only within the sensor range limits

NOTICE

Shortfall of the allowable working pressure!

Output of messages if pressure is too low.

‣

If a pressure smaller than the minimum permitted pressure is present at the device, the

messages "E120 Sensor low pressure" and "E727 Sensor pressure error - overrange" are

output in succession! Use the device only within the sensor range limits

7.1

Configuring messages

• The messages E727, E115 and E120 are "Error"-type messages and can be configured as a

"Warning" or an "Alarm". The factory setting for these messages is "Warning". This setting

prevents the BAD status from being transmitted in applications (e.g. cascade

measurement) where the user is aware of the risk of the sensor range being overshot.

• We recommend setting messages E727, E115 and E120 to "Alarm" in the following

instances:

– It is not necessary to violate the sensor range for the measuring application.

– A position adjustment must be carried out that has to correct a large measured error as

a result of the orientation of the device.

7.2

Function check

Carry out a post-installation and a post-connection check as per the checklist before

commissioning the device.
• "Post-installation check" checklist



see Section 4.4

• "Post-connection check" checklist



see Section 5.4

7.3

Commissioning via an FF configuration program

• The device is configured for the Pressure measuring mode as standard. The measuring

range and the unit in which the measured value is transmitted, as well as the digital output

value of the Analog Input Block OUT, correspond to the data on the nameplate. Following

a reset with code 7864, the OUT parameter may have to be rescaled (79, Section 7.9

"Scaling the OUT parameter").

• The standard order configuration is illustrated on



40, Section 6.3.6 "Deltabar S block

model".

1. Switch on the device.
2. Note the DEVICE_ID.



40, Section 6.3.5 "Device identification and addressing" and



10, Section 3.2.1 "Nameplates" for the device serial number.

3. Open the configuration program.
4. Load Cff and device description files into the host system or the configuration program.

Make sure you are using the right system files.

Содержание Deltabar S FMD77



















































































































Результаты поиска

Содержание Deltabar S FMD77

Отзывы:

Похожие инструкции для Deltabar S FMD77

Бренды по названию

Популярные бренды

Endress+Hauser Deltabar S FMD77, Руководство по эксплуатации

Результаты поиска

Содержание Deltabar S FMD77

Отзывы:

Похожие инструкции для Deltabar S FMD77

Бренды по названию

Популярные бренды