Endress+Hauser Deltabar FMD72 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 108

background image

Deltabar FMD72

Description of device parameters

87

X-value (040)/(123)/(193)

Navigation

Setup

®

Advanced Setup

®

Linearization

®

X-value (040)/(123)/(193)

Write permission

Operators/Service engineers/Expert

Description

Enter the X-value (level before linearization) for the specific point in the table and confirm.

Note

• If "Lin. mode" = "Manual", the level value must be entered.
• If "Lin. mode" = "Semiautomatic", the level value is displayed and has to be confirmed by entering

the paired Y-value.

Y-value (041)/(194)

Navigation

Setup

®

Advanced Setup

®

Linearization

®

Y-value (041)/(194)

Write permission

Operators/Service engineers/Expert

Description

Enter the Y-value (value after linearization) for the specific point in the table. The unit is determined
by "Unit after lin."

Note

The linearization table must be monotonic (increasing or decreasing).

Edit table (042)

Navigation

Setup

®

Advanced Setup

®

Linearization

®

Edit Table (042)

Write permission

Operators/Service engineers/Expert

Description

Select the function for entering the table.

Options

• Next point: enter the next point.
• Current point: stay on the current point to correct a mistake for example.
• Last input point: skip back to previous point to correct a mistake for example.
• Insert point: insert an additional point (see example below).
• Delete point: delete the current point (see example below).

Example

Add point, in this case between the 4th and 5th point for example

• Select point 5 via the "Line number" parameter.
• Select the "Insert point" option via the "Edit table" parameter.
• Point 5 is displayed for the "Line number" parameter. Enter new values for the "X-value" and "Y-

value" parameters.

Delete point, in this case the 5th point for example

• Select point 5 via the "Line number" parameter.
• Select the "Delete point" option via the "Edit table" parameter.
• The 5th point is deleted. All of the following points are pushed up one number i.e. following

deletion, the 6th point becomes Point 5.

«
...
85
86
87
88
89
...
»

Содержание Deltabar FMD72













































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar FMD72

Бренд: Acer Страницы: 2

Бренд: Acer Страницы: 4

Бренд: Kargo Master Страницы: 5

Бренд: Kappa Страницы: 4

Бренд: Campbell Страницы: 20

Бренд: Xylem Страницы: 60

Бренд: Camcar Страницы: 6

Бренд: RayTek Страницы: 2

Бренд: Ace Bayou Страницы: 8

Бренд: Hach Страницы: 44

Бренд: Habasit Страницы: 14

Бренд: Hama Страницы: 6

Бренд: Hama Страницы: 2

Бренд: Salta Страницы: 76

Бренд: Saft Страницы: 52

Бренд: Yeti Страницы: 19

Бренд: veba Страницы: 11

Бренд: Anslut Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды