Endress+Hauser Deltabar FMD72 Скачать руководство пользователя страница 65

Страница: 65 / 108

Deltabar FMD72

Diagnostics and troubleshooting

Diagnostics event

Cause

Corrective measure

Code

Description

S945

Pressure limit LP

• The configured overpressure or underpressure limit of

sensor module LP is exceeded.

• Sensor module LP defective.

• Check the pressure

value

• Change pressure limit

value

• Contact Endress

+Hauser Service

S971

Adjustment

• The current is outside the permitted range from 3.8 to

20.5 mA.

• The present pressure value is outside the configured

measuring range (but within the sensor module range,
if applicable).

• Check the pressure

value

• Check the measuring

range

• Check the setting

12.3

Response of output to errors

The behavior of the current output in case of fault is defined by the following parameters:

• "Alarm Behav. P (050)" (

88)

• "Output fail mode (190)" (

99)

• "High Alarm Curr. (052)" (

88)

12.4

Firmware version

Date

Firmwar
e version

Modifications

Documentation

CD-ROM

Operating Instructions

Description of Device
Parameters

Technical Information

01.2012 01.00.00

Original Firmware
Can be operated using
FieldCare from version
2.08.00

CD00520P/00/A2/01.12 BA01044P/00/EN/01.12 GP01013P/00/EN/01.12 TI01033P/00/EN/01.12

CD00520P/00/A2/02.12 BA01044P/00/EN/02.12 GP01013P/00/EN/02.12 TI01033P/00/EN/02.12

12.5

Disposal

When disposing, separate and recycle the device components based on the materials.

Содержание Deltabar FMD72













































































































Результаты поиска

Содержание Deltabar FMD72

Отзывы:

Похожие инструкции для Deltabar FMD72

Бренды по названию

Популярные бренды

Endress+Hauser Deltabar FMD72, Руководство по эксплуатации

Результаты поиска

Содержание Deltabar FMD72

Отзывы:

Похожие инструкции для Deltabar FMD72

Бренды по названию

Популярные бренды