Endress+Hauser Deltabar FMD72 Скачать руководство пользователя страница 88

Страница: 88 / 108

Description of device parameters

Deltabar FMD72

Factory setting

Current point

Tank content (043)

Navigation

Setup

Advanced Setup

Linearization

Tank Content (043)

Diagnosis

Measured values

Tank Content (043)

Write permission

Operators/Service engineers/Expert

Description

Displays the level value after linearization.

Alarm Behav. P (050)

Navigation

Setup

Advanced Setup

Current output

Alarm Behav. P (050)

Write permission

Operators/Service engineers/Expert

Description

Set current output if sensor module limits are overshot or undershot.

Options

• Warning

The device continues to measure. An error message is displayed.

• Alarm

The output signal assumes a value that can be defined by the "Output fail mode (190)/(051)"
function.

• Special

– The lower sensor module limit is undershot (sensor module LP or HP or complete system):

Current output = 3.6 mA

– The upper sensor module limit is overshot (sensor module LP or HP or complete system):

Current output assumes a value of 21 - 23 mA, depending on the setting of the "High Alarm
Curr." parameter (052).

Factory setting

Warning

High Alarm Curr. (052)

Navigation

Setup

Advanced Setup

Current Output

High Alarm Curr. (052)

Write permission

Operators/Service engineers/Expert

Description

Enter the current value for maximum alarm current. See also "Output fail mode".

Input range

21 to 23 mA

Factory setting

22 mA

Содержание Deltabar FMD72













































































































Результаты поиска

Содержание Deltabar FMD72

Отзывы:

Похожие инструкции для Deltabar FMD72

Бренды по названию

Популярные бренды

Endress+Hauser Deltabar FMD72, Руководство по эксплуатации

Результаты поиска

Содержание Deltabar FMD72

Отзывы:

Похожие инструкции для Deltabar FMD72

Бренды по названию

Популярные бренды