background image

Installation

Cleanfit P CPA472D

16

Hauser

3.4

Sensor installation

3.4.1

Preparing sensor and assembly

"

Caution! 
If turned in the opposite direction, the stop lock bolt does not engage. This could, however, loosen 
the sensor holder. The reason for this is adhesions on the lower part of the sensor holder. These can 
cause the sensor holder to get stuck, producing a counterforce when unscrewing the sensor holder.

1. Remove the protection cap from the sensor.

Make sure the sensor shaft is fitted with the 
O-ring and the thrust collar (Fig. 13).

2. Moisten the sensor shaft before installing the 

sensor.

3. Depending on the assembly version:

a.

Manually driven assembly:

Pull the retractable pipe as far as possible 
out of the assembly.

b.

Pneumatically driven assembly:

Move the assembly into the "Service" 
position.

4. Turn the stop lock bolt through 90° so that 

the plastic grooves are located above the 
recesses (Fig. 14, A).

5. Turn the retractable pipe 

clockwise 

until 

the stop lock bolt engages (B).

a0006214

Fig. 13: 

Sensor installation

1

Thrust collar and O-ring

a0002738

Fig. 14: 

Stop bolt

1

A

B

Содержание Cleanfit P CPA472D









































Отзывы: