Endress+Hauser analytikjena multi N/C pharma HT Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 125

background image

multi N/C pharma HT

Function and design

21

The top middle connection on the glass container is connected to the phosphoric acid
pump. The phosphoric acid pump pumps phosphoric acid (10 %) into the TIC reactor for
each TIC determination.

The cooling block dries the measuring gas by freezing out the water vapor. The dry mea-
suring gas is routed via the top connection out of the TIC condensate container. The
measuring gas drying is maintenance-free.

The condensate pump pumps the condensate or waste solution from the TIC determina-
tion out via the bottom side outlet on the glass container after each measurement

Figure 12TIC condensation module

1 TIC condensate container

2 Connection for hose 1/condensation coil

measuring gas feed

3 Cooling block

4 Connection to the water traps

5 Water traps

6 Connection for hose AD/phosphoric acid

feed

7 Connection for hose BB/direct sample

feed for TIC detection

8 Connection to condensate pump (waste

hose 11)

Water traps

The water traps remove interfering components from the measuring gas and protect the
detector and the gas box. The water traps are mounted in the gas path behind the cool-
ing block or behind the gas box. The water traps each consist of a larger and a smaller
water trap. The larger water trap (TC prefilter) retains aerosols during operation. The
smaller water trap (disposable retention filter) retains rising water.

«
...
19
20
21
22
23
...
»

Содержание analytikjena multi N/C pharma HT






























































































































Отзывы:

Нет отзывов

Похожие инструкции для analytikjena multi N/C pharma HT

Бренд: ABB Страницы: 8

Бренд: ICM Controls Страницы: 8

Бренд: WAGO Страницы: 96

Бренд: Garmin Страницы: 22

Бренд: Percussion Play Страницы: 3

Smart Probes 115i

Бренд: TESTO Страницы: 17

CoolPoint CP12-V8

Бренд: UFM Страницы: 14

Nitro-Save NS16

Бренд: TDI Страницы: 4

Бренд: JUMO Страницы: 24

Бренд: Raytech Страницы: 7

Бренд: AEMC Страницы: 20

Бренд: General Страницы: 12

Бренд: B meters Страницы: 3

Бренд: YoloLIV Страницы: 18

RADIATION ALERT Sentry

Бренд: S.E. International Страницы: 8

Бренд: Fluke Страницы: 97

Optical Power Expert

Бренд: EXFO Страницы: 93

Бренд: Badger Meter Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды