Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 71

Страница: 71 / 124

multi X 2500

AOX determination

Insert the storage container for the combined electrode into

the bracket in the door of the chlorine module.

Insert the combined electrode into the opening of the

measuring cell.

Insert the measuring gas hose from the sulfuric acid

container using the Teflon connector (1) into the connection

of the combined electrode.

Connect the olive-tip suction adapter to the exhaust air hose

in the chlorine module.

Connecting the combined electrode and the measuring cell at

the inside of the rear panel of the chlorine module:



Connection combined electrode (1)



Connection measuring cell (2)

6.3.2

Preparing the measuring cell

The preparation of the measuring cell for daily measurements includes the following

steps:



Preparation of the electrolyte solution



Execution of the end point routine

See chapter "Preparing the measuring cell", p. 59 for information on how to prepare

the measuring cells "sensitive" and "high concentration".

Содержание Analytik Jena Multi X 2500





























































































































Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena Multi X 2500, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena Multi X 2500

Отзывы:

Похожие инструкции для Analytik Jena Multi X 2500

Бренды по названию

Популярные бренды