manualshive.com logo in svg

ENDEVCO 133, Инструкция по эксплуатации

Поделиться
Скачать
ENDEVCO 133 Скачать руководство пользователя страница 20

 

 

ENDEVCO

    www.endevco.com    Tel: +1 (866) ENDEVCO  [+1 (866) 363-3826] 

IM133, Page 20 

®

 

2.4.9  Sample Set Up 
 
 

The following information is intended for the first time or infrequent user of this amplifier.   

 
 

A.  Using figure 1 as a reference, perform the following initial setups: 

 

 

1.  Using the "Select Channel" button, select channel 1.  (The LED illuminated is the channel 

that is being monitored by the DPM.) 

 

 

 

2.  Using the "Select Function" button, select the appropriate sensor type.  While the LED is 

flashing for the Input Select function, press the "Edit" button directly above or below the word "Edit" 
on the front panel.  This will cause the DPM to display either "Chrg" or "Volt".  Once the appropriate 
sensor type is selected, press the "Select Function" button to save that configuration of input and the 
"Select Function" LED will automatically advance to the next function.  (Assume a PE accelerometer 
is used with a sensitivity of 10.04 pC/g.) 

 
 

 

3.  With the "Current Exc. (mA)" LED flashing, use the button directly above or below the 

word "Edit" to select either 0, 4 or 10 mA.  If, in step two above, the configuration was set for a "Chrg" 
type  input  then  the  current  level  will  not  affect  the  charge-type  accelerometer.    If  a  voltage  or 
ISOTRON accelerometer was selected, then it is acceptable to set the current level to 4 mA as a 
starting point.  (Only one common current level may be set for all three channels.)  (Assume a PE 
accelerometer is used, so any selection is acceptable.) 

 
 

 

4.  Press the "Select Function" button to advance to "Sensitivity (pC or mV/EU)".  While the 

LED is flashing, enter the correct sensitivity value of the sensor being used.  (This is accomplished 
with the top and bottom "Edit" buttons to increase or decrease the value.  The left and right "Edit" 
buttons move the digiton the DPM to be changed.  The actual value must be within the range of 
0.001 to 9999.)  Using the same assumption, input 10.04 on the DPM.) 

 
 

 

5.  Press the "Select Function" button to advance to "Output Scaling (mV/EU)".  While the 

LED is flashing, enter in an appropriate value, which must be within the following limits: (The scaling 
value  entered  is  valid  for  0.001  to  9999  along  with  the  following  limitation:    0 

≤

  Output  Scaling  / 

Sensor sensitivity 

≤

 1000.   

 
 

To better understand the correct scaling value to enter, the following questions must be answered: 

 

 

 

a.  What is the desired full scale output voltage? 

 

 

 

b.  What is the maximum g range to be measured (in g's or EU)? 

 

 

 

c.  What is the sensor sensitivity? 

 

 

 

 
 

 

 

Metal Shield
     Cover

Unit Front

Power Supply

Filter Modules

Channel 1

Channel 2

Channel 3

Figure  7

(Shown cut
away to
expose the
circuit board
and filter
locations.)

Содержание 133






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды