Enconnex ECX-ER3P-42UXX Скачать руководство пользователя

Страница: 7 / 48

General Safety Precautions

1.1 Overview

Enconnex is not responsible for any of the following situations:

•

Operation of equipment in adverse environments beyond the manual
instructions.

•

Any installation and operation environment beyond regulations of any
relevant international standards.

•

Altering of the product or changes in the software without prior
approval.

•

Failure to follow the product and manual’s operational instructions and
safety warnings. See the end of this manual for further details.

•

Equipment damage caused by natural disasters.

1.2 Local Rules and Regulations

Local rules and regulations should be followed during equipment operation.
Safety precautions in the manual serve as a supplementary guide to local
safety specifications.

1.3 Basic Installation Requirements

Personnel performing the EdgeRack 3P installation and maintenance must
receive authorized training.

•

Equipment installation, operation, and maintenance can only be
conducted by qualified and trained people.

•

Replacing and changing equipment or components (including software)
must be completed by professionals with Enconnex certification or
authorization.

•

Operators should immediately report faults or errors which may cause
safety issues.

Содержание ECX-ER3P-42UXX

















































Результаты поиска

Содержание ECX-ER3P-42UXX

Отзывы:

Похожие инструкции для ECX-ER3P-42UXX

Бренды по названию

Популярные бренды

Enconnex ECX-ER3P-42UXX, Руководство пользователя

Результаты поиска

Содержание ECX-ER3P-42UXX

Отзывы:

Похожие инструкции для ECX-ER3P-42UXX

Бренды по названию

Популярные бренды