Emulex LPe11002 HBA Скачать руководство пользователя страница 2

LPe11002  Hardware Installation Manual

Page ii

 

Copyright© 2005 Emulex Corporation. All rights reserved worldwide. No part of this document may be reproduced 
by any means nor translated to any electronic medium without the written consent of Emulex Corporation.

Information furnished by Emulex Corporation is believed to be accurate and reliable. However, no responsibility is 
assumed by Emulex Corporation for its use; or for any infringements of patents or other rights of third parties which 
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Emulex 
Corporation.

Emulex and LightPulse are registered trademarks, and AutoPilot Installer, AutoPilot Manager, BlockGuard, 
FibreSpy, HBAnyware, InSpeed, MultiPulse, SLI and SBOD are trademarks, of Emulex Corporation. All other brand 
or product names referenced herein are trademarks or registered trademarks of their respective companies or 
organizations.

Emulex provides this manual "as is" without any warranty of any kind, either expressed or implied, including but not 
limited to the implied warranties of merchantability or fitness for a particular purpose. Emulex Corporation may 
make improvements and changes to the product described in this manual at any time and without any notice. Emulex 
Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties 
that may result. Periodic changes are made to information contained herein; although these changes will be 
incorporated into new editions of this manual, Emulex Corporation disclaims any undertaking to give notice of such 
changes.

Содержание LPe11002 HBA


















Отзывы: