Emulex LP1050DC Скачать руководство пользователя страница 15

Laser Safety Notice

This laser safety information contains certification and product information covering 

laser products known as optical Gigabaud Link Modules (GLMs), Gigabit Interface 

Converters (GBICs), 1x9 and small form factor transceivers sold as accessories to or 

incorporated in Emulex LightPulse host adapters. The GLM, GBIC, 1x9 and small form 

factor transceiver are the primary cable connection mechanisms for any optical port on 

the host adapter and hub. This data is not intended to be a replacement for any safety 

regulations and standards; relevant safety documents should always be consulted if 

necessary. Contact Emulex Corporation with any questions or concerns about laser 

safety.

Certification and Classification

Labeling Requirements

Product Information

Usage Restrictions

System Level Certification

Certification and Classification

LP6000 and LP7000E PCI host adapters may contain a laser product known as an 

optical Gigabaud Link Module (GLM). The optical GLM is attached to the host 

adapter using an 80-pin connector and extends through the mounting bracket. In 

turn, the host adapter can be inserted into any host system's PCI slot.

The LH5000 hub may contain a laser product known as a Gigabit Interface 

Connector (GBIC). The GBIC provides the physical connector to the optical cable. 

The GBIC can be inserted into any pluggable hub port.

The LP8000, LP850 and LP9000 PCI host adapter may contain a laser product 

known as a Gigabit Interface Converter (GBIC) or an embedded 1x9 transceiver. 

The GBIC and or 1x9 transceiver provide the physical connection to the optical 

cable, and its SC-style connector extends through the mounting bracket. In turn, the 

host adapter can be inserted into any host system’s PCI slot.

The LP9002, LP9002L, LP952L, LP9002S, LP9002DC, LP9002C, LP9402DC, 

LP9802, LP982, LP9802DC, LP10000, LP10000DC, LP1050DC and LP1050 host 

adapters may contain a laser product known as a small form factor transceiver. This 

transceiver provides the physical connection to the optical cable, and its LC-style 

connector extends through the mounting bracket. In turn, the host adapter can be 

inserted into any host system's appropriate PCI/PCI-X/cPCI/SBus expansion slot.

Emulex Documentation, Drivers and Software

15

Содержание LP1050DC





















Отзывы: