EMS EMS827 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 60

EMS EMS827 Скачать руководство пользователя страница 25

EMS 827

GENSET CONTROLLER

Confidential

Page 25

Message

Function description

Check the canopy temperature sensor and associated wiring.

Fuel-L Fault

The Fuel Level Sensor is not functioning as expected.

Check the Fuel Level Sensor and associated wiring.

Speed Fault

The Speed Sensing system is not working as expected.

Check  the  associated  speed  sensor  wiring  and  external  influences
such  as  poorly  operating  battery  chargers  and  poorly  filtered  UPS
systems connect to the load.

Speed Detected

Speed signal is unexpectedly present.

Check  the  associated  speed  sensor  wiring  and  external  influences
such  as  poorly  operating  battery  chargers  and  poorly  filtered  UPS
systems  connected  to  the  load.    Check  electrical  safety  earthing
systems.    Check  associated  communications  networks  are  isolated
and not part of an unexpected earth loop.

Oil Detected

Oil Pressure is unexpectedly present.

Check the Oil Pressure Sensors and associated wiring.

Check the Oil filter system is not blocked.

Check the engine is not running with a failed speed sensing system.

E-S Lock-out

The emergency stop input has been activated. Deactivate the
emergency stop input, then press the stop button to clear this
alarm.

Fire Alarm

The Fire Alarm input has been activated. The genset will be
shutdown as an emergency stop. Investigate the source of the
alarm then press the stop button to clear this alarm

A-S Lock-out

If the Stop button is pressed while running in auto mode, it is
considered an emergency stop and the unit will stop the engine and
enter the Autostart Lockout state. This prevents the engine from
starting again, while the Autostart input remains activated.

The Autostart Lockout state is self resetting upon deactivation of
the Autostart input.

If the engine was stopped for a real emergency, then the
emergency stop switch should also be activated to ensure the
engine will not start inadvertently.

If  the  unit  is  in  the  Autostart  Lockout  state,  the  engine  can  be
restarted  by  pressing  the  Start  button.    This  is  not  considered  a
manual  start  but  rather  a  release  from  the  Autostart  Lockout
condition.    The  contactors  will  be  controlled  in  the  appropriate
way.

«
...
23
24
25
26
27
...
»

Содержание EMS827





























































Отзывы:

Нет отзывов