manualshive.com logo in svg

Empire Comfort Systems P)-6, Инструкция по установке и руководство пользователя, Страница: 56 / 76

Поделиться
Скачать
Empire Comfort Systems P)-6 Скачать руководство пользователя страница 56

31447-5-0214

Page 56

Brief Description of the Components

The gas valve is fitted with a manual HI/LO knob to allow for man

-

ual modulation of the gas outlet pressure to the appliance burner. 

The controls are designed to be used with either LPG or Natural 

Gas and can be converted by use of an OEM supplied conversion 

kit.

The Digital Fireplace Control (DFC) is an automatic gas ignition 

system based on a single microcontroller core. This control man-

ages all functions related to ignition, flame sensing and supervi

-

sion for atmospheric applications. 

The DFC can be set to provide continuous or intermittent ignition 

control sequences and flame monitoring with safety shutdown in 

case of failure.

The DFC is set up as a stand alone (AC powered system with 

battery back up. See Lighting Instructions on page 55 and Wiring 

Diagram on page 54.

Troubleshooting

Before proceeding with the procedures in the following trouble-

shooting table, verify that the power supply (AC/DC adapter) is 

present and that the batteries inside the receiver and/or optional 

battery pack are fresh and installed with correct polarity.

Make sure all the connections between the wire harnesses and 

system components are proper and positive.

Verify that the static inlet pressure meets the manufacturer’s rec-

ommended inlet pressure. If necessary adjust the line pressure 

regulator.

If the recommended actions for the following troubleshooting chart 

do not help to address the problem consider replacing wiring har-

nesses.

WARNING

:

Any actions performed on the gas valve must be performed 

in accordance with this instruction manual. Likewise, any 

actions performed on the DFC or other system components 

must be done in accordance with the individual component 

instructions. 

Replacement of components must be performed in accor-

dance with this instructions manual.

INTERMITTENT PILOT CONTROL SYSTEM TROUBLESHOOTING

Содержание P)-6













































































Отзывы:

Нет отзывов