manualshive.com logo in svg

Empire Comfort Systems P)-6, Инструкция по установке и руководство пользователя, Страница: 1 / 76

Поделиться
Скачать
Empire Comfort Systems P)-6 Скачать руководство пользователя страница 1

Page 1

DIRECT VENT GAS FIREPLACE 

HEATER

MILLIVOLT STANDING PILOT

DVP36FP3(0,1,2,3)(N,P)-5

DIRECT IGNITION

DVP36FP5(0,1,2,3)N-1

INTERMITTENT PILOT

DVP36FP7(0,1,2,3)(N,P)-6

REMOTE RF

DVP36FP9(1,3)(N,P)-6

UL FILE NO. MH30033

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL 

WARNING

: 

: If not installed, operated and main-

tained in accordance with the manufacturer’s instruc-

tions, this product could expose you to substances 

in fuel or from fuel combustion which can cause death 

or serious illness.

This appliance may be installed in an aftermarket, 

permanently located, manufactured home (USA only) 

or mobile home, where not prohibited by state or local 

codes.
This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gases, unless a certified 

kit is used.

Direct Vent Zero Clearance Gas  

Fireplace Heater

GAS-FIRED

Installer: 

Leave this manual with the appliance.

Consumer:  Retain this manual for future reference.

—  Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 

other appliance.

—  WHAT TO DO IF YOU SMELL GAS

 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use 

any phone in your building.

  •  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 

instructions.

 

•  If you cannot reach your gas supplier, call the 

fire department.

—  Installation and service must be performed by a 

qualified installer, service agency or the gas sup

-

plier.

WARNING

: 

: If the information in these instruc-

tions are not followed exactly, a fire or explosion 

may result causing property damage, personal in-

jury or loss of life.

EMPIRE

EMPIRE

Comfort Systems

Содержание P)-6













































































Отзывы:

Нет отзывов