Emotion Tech MicroDelta Rework Скачать руководство пользователя страница 38

Страница: 38 / 42

Appendix

Documentation Version 1.2.6

Maintenance

A monthly maintenance of the 3D printer is recommended.

Below are some recommendations:

Using a brush, dedust the following:

• Emotronic board

• All the fans to ensure a good airflow

• Cold part of the printhead

- To clean the printhead follow the guide dedicated to the Hexagon hotend on the following link:

http://data.emotion-tech.com/highlights_fr/Hexagon%20-%20Notice%20montage-debouchage.pdf

- Clean the teeth of the drive wheel using a sharp ended tool like a needle tip, the end of tweezers or a cutter blade.

- Check & tighten the screws of the 3D printer.

- Lubricate the various mechanical transmission elements with multipurpose grease.

Recommandations

Turning off your 3D printer :

After printing, if you want to turn off the machine, wait until the print head cools down to room temperature to

ensure that the print head doesnt get clugged.

Transport :

If the printer has to be transported by car or another mean of transport in which it could be subject to vibration, it is

recommended to unplug all the motors from the eMotronic board to avoid damaging it.

Troubleshooting :

A FAQ on the MicroDelta Rework is available on our website in the «Support» section, please refer to it

to troubleshoot your printer, most problems could be solved through this tool !

Содержание MicroDelta Rework











































Результаты поиска

Содержание MicroDelta Rework

Отзывы:

Бренды по названию

Популярные бренды

Emotion Tech MicroDelta Rework, Руководство пользователя

Результаты поиска

Содержание MicroDelta Rework

Отзывы:

Бренды по названию

Популярные бренды