background image

3

•  Do not open the device. Repairs must be done by a professional only. Improper use or unskilled 

repair can cause injury by electric current, or short circuit. 

•  Signal range is always provided as maximum in an open area without obstacles and may be 

significantly affected by the construction material used in the building where the device is 

installed. The signal range also depends on the placement of the transmitter and receiver. 

Avoid placing parts of the device in the proximity of heat sources, areas with increased air 

humidity, sources of electromagnetic radiation, power conductors and large metal objects. 

Information for use 

The wireless set of sockets can be used immediately after unpacking. Receiver – socket: The socket 

can be plugged into any wall-mounted socket. The device which is to be wirelessly controlled must 

be plugged into the wireless socket. The wirelessly controlled appliance must always be turned on. 

Remote controller – transmitter 

•  Open the battery compartment cover and remove the protective film. Close the cover.

•  A socket can be assigned to each of the A, B, C, D button pairs. 

•  Each pair of buttons works separately. The left-side buttons turn the corresponding socket on, 

the right-side buttons turn it off. 

•  The red LED light indicates signal transmission. 

Replacing battery in the remote controller

•  Open the battery compartment cover at the back of the remote controller.

•  Remove the used battery.

•  Insert a new CR2032 3 V battery. Make sure you observe the correct polarity. Use primary 

batteries only, not rechargeable ones.

•  Close the cover.

Socket – receiver

•  Insert the male plug of the remote-controlled socket into a 230 V~ network socket. 

•  The ON/OFF button located on the socket is used for manually turning the connection on and off 

and also serves for the activation of the pairing process of the socket and the remote controller. 

•  The light on the socket is on only if the socket is turned on. It begins flashing when the socket 

is ready for pairing. 

Settings – pairing socket with a remote controller

•  Insert the male plug of the remote-controlled socket into a 230 V~ network socket. 

•  Press and hold the ON/OFF button located on the socket for 3 seconds, then release the 

button. The LED light will start flashing. This indicates that the socket is ready for pairing with 

the remote controller. 

•  Put the remote controller in the proximity of the socket and press any button on the left side 

of the controller, A to D, to pair the codes. The LED light will now remain on. This indicates the 

pairing has been done successfully.

•  Connect an electrical appliance into the socket and turn it on. 

•  Press the corresponding ON button on the remote controller to turn on the socket. The LED 

light on the socket will turn on, indicating the socket is running. 

•  You can pair other sockets with the remote controller using the above method. 

•  If you make a mistake during pairing and need to make changes, press and hold the button 

on the socket for 6 seconds and release. The LED light will start flashing and turn off after 

3 seconds. The set values are now erased.

•  Maintain the minimum distance of wireless sockets from one another. When in use, the sockets 

should be more than 50 cm apart. 

Important Warning 

•  Only a connecting cable can be connected into the remote-controlled socket (not an appliance 

with a direct plug). 

•  The remote-controlled sockets must be connected to a 230 V~/50 Hz power network fitted 

with circuit protection.

•  Only appliances powered by 230 V~/50 Hz voltage can be connected to the sockets.

•  Pay attention to the data on the type label of the appliances connected to the device.

Содержание P0065













Отзывы: