background image

 

© 2017 Copyright EMG INC. All Rights Reserved.

PO BOX 4394 
SANTA ROSA, CA
95402  USA

P (707) 525-9941
F  (707) 575-7046
EMGPICKUPS.COM

0230-0330rA

INSTALLATION INFORMATION

 

EMG MODELS:

 RETRO ACTIVE S/S/S SET

Maverick Five (Alnico 5) and Crossroads (Alnico 2) 

Warranty

All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If 

upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This 

warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.   

3.28

2.75

3.00

.70

6/32 MOUNTING SCREWS

.412 TYP

RA-Crossroads (A2)

RA-Maverick Five (A5)

Installation notes:

 

All EMG Pickups are compatible with each other. The connector system is an easy method of installation, avoiding the need to solder. 

Older systems may need to be soldered, while the newer systems can be easily connected and modified. If you have an older EMG 

Pickup you can install the new system along with it. 

EMG accessories like the VLPF, EXG, SPC or RPC Controls can be added to any EMG Pickup System without the need for an extra battery.

IMPORTANT INSTALLATION NOTES:

 

1) Only one 9-Volt battery is required to power the pickups and any

     accessories such as the SPC, RPC, EXG, AB, PA-2, and Pi-2. 

     Use an Alkaline or Lithium battery for longest life.  

2) The Volume and Tone controls included with this EMG System are

     25K Ohm. This value is required for the system to work correctly.             

3) A stereo output jack (12B) is included with the EMG Pickups; 

     it grounds the black battery wire to turn on the pickups when   

     the plug is inserted into the jack. If you are replacing passive

     pickups, make sure to use the jack included. If your guitar has a

     long panel jack make sure it is a stereo type, a Switchcraft 152B

     is recommended.

 4) When installing EMG Active Pickups, DO NOT connect the bridge

     ground wire. This wire is usually soldered to a volume or tone

     control casing and goes to the bridge. This wire grounds the

     strings and uses them and your body as a shield against hum and

     buzz. It also creates a shock hazard.

     

    

 EMG Pickups are shielded internally and DO NOT require string        

     grounding. This greatly reduces the possibility of reverse 

     polarity shock from microphones and other equipment.  

5) EMG Active Pickups have very little magnetism compared to 

     passive pickups. We recommend you adjust the pickups as 

     close to the strings as possible. Sustain and string movement 

     will not be inhibited by close adjustment. Models EMG-SV,

     EMG-SAV, and EMG-SLV feature magnetic pole pieces which can

     inhibit intonation and string movement.  

 

6) If your installation is different from the diagrams in these 

     instructions or you need additional diagrams visit our website: 

     emgpickups.com for a complete listing of available diagrams.

 

SPECIFICATIONS:

MODEL

    Maverick 

Five 

Set 

 

 

Crossroads Set

Logo Color 

                           

Gold 

Gold 

Gold 

 

Gold 

Gold 

Gold 

Magnet 

Type 

  A5 

A5 

A5 

 A2 

A2 

A2

Gauss Strength at Poles 

 

750 

750 

750 

 

600 

600 

600

Resonant 

Frequency 

(KHz) 

 

4.75 3.50 3.00  

4.50 3.30 2.90 

Output 

Voltage 

(String)   

1.00 1.00 1.00  

1.00 1.00 1.00

Output Voltage (Strum) 

 

3.00 

3.00 

3.00 

 

3.00 

3.00 

3.00

Output Noise (60 Hz) 

 

-103 

-103 

-103 

 

-103 

-103 

-103

Output Impedance (Kohm) 

 

 

3

System Current @9V (Microamps) 

630 

630 

630 

 

630 

630 

630

System Battery Life (Hours)   

830 

830 

830 

 

830 

830 

830

Maximum 

Supply 

(Volts 

DC) 

 

27 27 27  

27 27 27

NECK MID

 

BRIDGE  

NECK 

MID

 

BRIDGE

 

.490 (12.44)

RED

BLK

WHT

EMG B315rA

.770 (19.5)

*Note:  Magnet Type: A5 (Alnico 5) A2 (Alnico 2)

**Note: Specifications shown are for the entire 3 pickup system 

   

                                 

                                 

Содержание RETRO ACTIVE Series

Страница 1: ...ted into the jack If you are replacing passive pickups make sure to use the jack included If your guitar has a long panel jack make sure it is a stereo type a Switchcraft 152B is recommended 4 When installing EMG Active Pickups DO NOT connect the bridge ground wire This wire is usually soldered to a volume or tone control casing and goes to the bridge This wire grounds the strings and uses them an...

Страница 2: ...jack will be required see the Power Tips Data sheet at http www emgpickups com 2 Some instruments may already have a battery holder installed and in that case soldering may be required see page 3 Installing EMG Combination Systems is very easy and is accomplished in a few steps The controls included have a 10 mm bushing height so they can be used either on a pickguard or body mount The cable lengt...

Страница 3: ...nting down Refer to the diagrams below and make sure the Jack is mounted tightly Step Five Route the Output cable from the Jack cavity into the control cavity via the small hole If the hole is too small Push the connectors through one at a time Fasten the Jack plate onto the guitar and test to make sure the cable inserts and exits easily Mount the battery in the control compartment Insulate the ba...

Страница 4: ...r refer to the diagram at the right Retro Active S S S COMBINATION SYSTEM INSTRUCTIONS Page 4 Step Six 1 Plug the Output Cable from the PC Board GND SIG to the Volume Control 2 Plug the Output cable from the Output Jack onto the Volume control as shown 3 Plug the green wire onto the Ring terminal of the Switch PC Board Step Seven Plug the Battery clip cable onto the BAT BLACK and the BAT RED termi...

Отзывы: