background image

High Frequency (Treble) Response Selection:

The BQC has the added feature of allowing you to choose from 4 different
high frequency response curves. This is a nice feature especially if you are 
using the BQC with passive pickups. The following diagrams show the dip-switch 
positions and the graphs show the resultant frequency response.
The BQC Control is an equalizer style control, offering both boost and cut
at the same frequency locations. The control also features a center detent 
(click) that lets you know when no equalization is in effect.

Low Frequency (Bass) Response:

The BQC has a fairly standard bass response boost and cut. Its slope is 
6dB per octave and is centered at 50Hz. As you can see in the graph 
on the left the signal can be boosted by +12db (Red Line) or cut by 
-12dB (Green Line). A center detent (click) is provided on the control 
to let you know when the  frequency response is flat or unaffected 
by boosting or cutting.

Mid-Range Frequency Response:

One of the primary features of the BQC is it’s mid-range control. It allows you to 
choose the frequency you want to boost or cut from 100 to 1000 Hz. The concentric
mid-range pot has two sections. The lower control chooses the frequency, while the
upper control lets you choose the amount of boost or cut you want. The maximum slope
is 12dB per octave at full gain or cut.. There is also a center detent (click) in the center
of the upper control to let you know when the control is not having any effect. 

MID FREQUENCY SELECTION (LOWER CONTROL)

MID BOOST OR CUT (UPPER CONTROL)

BASS BOOST OR CUT (LOWER CONTROL)

TREBLE BOOST OR CUT (UPPER CONTROL)

BASS/TREBLE
   CONTROL

BQC-HZ System Page 2

Installation Instructions: 
EMG Model: BQC-HZ System

10KHz

1KHz

20Hz

10 dB/div

BQC CONTROL BASS RESPONSE

10KHz

1KHz

20Hz

10 dB/div

ON/ON

BQC CONTROL (TREBLE RESPONSE: ON/ON)

10KHz

1KHz

20Hz

10 dB/div

OFF/ON

BQC CONTROL (TREBLE RESPONSE: 1 OFF/2 ON)

10KHz

1KHz

20Hz

10 dB/div

OFF/OFF

BQC CONTROL (TREBLE RESPONSE: 1 OFF/2 OFF)

10KHz

1KHz

20Hz

10 dB/div

ON/OFF

BQC CONTROL (TREBLE RESPONSE: 1 ON/2 OFF)

VARIABLE MID-RANGE FREQUENCY

1.0KHz

100Hz

20Hz

10 dB/div

10KHz

1KHz

Содержание BQC-HZ SYSTEM

Страница 1: ...jack If this isn t possible it s no worry either wiring order is acceptable ABOUT THE BQC HZ SYSTEM The BQC HZ System is a complete control system for bass guitars Active Balance Master Volume and EQ circuits are included The EQ effects are illustrated in the graphs on the next page They allow you separate control over bass midrange and treble Rotate the controls clockwise to boost counterclockwis...

Страница 2: ...ency Response One of the primary features of the BQC is it s mid range control It allows you to choose the frequency you want to boost or cut from 100 to 1000 Hz The concentric mid range pot has two sections The lower control chooses the frequency while the upper control lets you choose the amount of boost or cut you want The maximum slope is 12dB per octave at full gain or cut There is also a cen...

Страница 3: ...her pin when using passive pickups EMG INC B125rC BRG NEK GND IN V NK IN BR IN OUT GND V GND GND Bridge Pickup Cable Neck Pickup Cable Solder Pickup Hot Red Wire to BRG Pad Solder Pickup Ground Green Braid to GND Pad Solder Pickup Ground Green Braid to GND Pad Solder Pickup Hot Red Wire to NEK Pad MASTER VOLUME VOLUME B122rH BQC HZ System Page 3 Installation Instructions EMG Model BQC HZ System So...

Страница 4: ...minal of the Output Jack RED TO BATTERY BUSS 18Volts Diagram 6 9V 9V T R S RED BLACK 18 Volt Wiring Option If you want to operate your instrument at 18 Volts for more headroom then use 2 batteries wired as below Also if you are using any type of EQ in your instrument EMG BT BQ or anything that boosts the pickup signal then 18 Volts is recommended Solder the Black and Red wires together and cover t...

Отзывы: