Unsuccessful connection
Device will make low tone sounds. Red and
green lights flash alternately again. This means
device has returned to state it was in step 6
(Access Point mode). Please try again starting
from step 6 and make sure you typed your own
Wi-Fi network password correctly.*
Red and green lights are flashing alternately.
*Still cannot connect? Please see chapter
Troubleshooting in “Installation & operating
instructions” (
https://qs.emfit.com/docs)
.
Connect the power cord to Emfit QS.
Upon powering the device will scan all
available Wi-Fi networks. Note this especially
using a mobile device as hotspot Wi-Fi .
2.
3.
5.
4.
6.
7.
This g
uide
1.
Sensor
EMFIT QS
with Wi-Fi transceiver
Data signal
Keep electronic unit
minimum of 30 cm
distance away from body.
8
A password is requested.
Emfit XXX is requesting
WPA2-password
Password:
Show the password
Remember this network
Cancel
OK
A) New device setup
Page 1
Select a suitable adapter.
1
2
Connect the correct adapter.
Ensure that it locks in its place.
CLICK!
3
Connect the power supply to electrical outlet
(110 - 230V AC).
Power cord
4
Power cord
Sensor cord
Power cord
5
Green and red lights start to flash alternately
and device makes beep sounds.
Green
Red
Green
Red
Green
Green
Green
Red
Red
Red
…
Sensor cord
7
Ignore possible “No internet connection”.
Select and connect to the network:
Emfit_xxxxxx
(where xxxxxx is the serial num-
ber of your device).
Windows
Networks
Connections
Wi-Fi
Connected
Network
Emfit_1234567
Some-Guest-2.4GHz
2WIRE123
Mac OSX
Turn Wi-Fi Off
Emfit_1234567
AppleWiFi
Testwork
Join Other Network…
Create Network…
Open Network Preferences…
Wi-Fi: On
With your computing device scan for wireless
networks.
6
Computing device
SCANNING
9
Emfit Ltd, Finland | Product: Emfit QS | Model: IP-9360
Contains FCC ID: W70MRF24WG0MAMB
Contains transmitter module IC:
7693A-24WG0MAMB
Designed and manufactured in Finland.
SN: XXXXXX
PIN: XXXXX
PW: XXX-XXXX-XXX
http://192.168.1.3
Find the password at the back of the Emfit QS
device (PW: XXX-XXXX-XXX).
Note! The password must be filled in with the
hyphens.
12
Press enter and EMFIT QS will now try to con-
nect to your Wi-Fi network. Connecting can
take up to few minutes. You hear short “beep”
sounds and see the red led flashing.
Red light starts flashing.
11
Select your own Wi-Fi network from the list,
type its password and click enter.
If you do not see your wireless network,
please notice what is said in Step 5.
If you still cannot find your Wi-Fi network,
please see chapter Troubleshooting in
“Installation & operating instructions”
(https://qs.emfit.com/docs).
http://192.168.1.3
Emfit
“Your network”
Detected Wireless Networks
Other Network…
13
Successful connection
Device will make high tone sounds. This means
that the password you typed is correct. To ver-
ify succesful connection, ensure the sensor is
not sensing any vibration and is preferably un-
der the mattress; see section C 22–25.
In about 1-3 minutes either green light will start
flashing, or red light alone will keep flashing. If the
later, please contact Emfit support:
Email: [email protected]
Phone: USA (512) 266-6950, EU +358 20 778 0870
14
1. Sensor with attached signal conditioner and Wi-Fi module
2. Power supply
3. Plug adapter for European countries
4. Plug adapter for United Kingdom
5. Plug adapter for USA and Canada
6. Plug adapter for Australia
7. This guide
Package contents
This Quick Guide contains information extracted from the instructions
for use.
Please read the “Installation & operating instructions” for the
full instructions for use, including information on safety from:
https://qs.emfit.com/docs
Overview
10
Open your computing device’s browser
(Mozilla, Safari, Chrome, Internet Explorer etc.).
Type in address/url bar:
http://192.168.1.3
and press enter.
If you cannot access above IP-address,
please see chapter Troubleshooting in
“Installation & operating instructions”
(
https://qs.emfit.com/docs)
.
http://192.168.1.3
The 5 GHz Wi-Fi is not supported.
Wi-Fi channels 12 , 13 and 14 are not supported.
This concerns European customers especially.
2.4 GHz Wi-Fi is supported.
Wi-Fi channels 1 - 11 are supported.
or
To operate, EMFIT QS needs Internet
connection. It can be either:
Wi-Fi requirements
Your Wi-Fi network password
Home Wi-Fi
with Internet access
A
Mobile device as
Wi-Fi hotspot
Your hotspot Wi-Fi network password
B
A computing device*
(computer or tablet or smartphone
with browser)
To set up the Wi-Fi you need
(once):
Note! Make sure address starts with
http
and not https!
If only the red led flashes you need to restore the de-
vice into AP mode. Please see chapter Restoring Emfit
QS device to Access Point (AP) mode in “Installation &
operating instructions”
(https://qs.emfit.com/docs)
.
* NOTE! Also for you need an additional
computing device for setup
If you do not know whether your home Wi-Fi is compatible, please see chapter Troubleshooting in
“Installation & operating instructions” (
https://qs.emfit.com/docs)
.
Safety instructions
If the device gets wet or starts overheating stop using
immediately and disconnect power
supply from mains power.
Equipment is not suitable for use in the presence of a
flammable anaesthetic mixture with air
or with oxygen or nitrous oxide.
Only use the power supply (as specified in chapter
Technical specifications) supplied with the product.
This product is designed for indoor use only.
This product IS NOT intended to be used for direct
diagnosis or monitoring of disease or
other conditions, or physiological processes.
Do not use this device for any purpose other than
that specified by the manufacturer.
Do not try to repair the device yourself.
If the instructions are not adhered to, the situation may lead to a death or serious personal injury (in these instructions for use).
ATTENTION - consult accompanying documents (i.e. these instructions for use)
Means that the section contains important information for the user (in these instructions for use).
The EMFIT QS hardware (Product) and web application (Service) together is a general
wellness product intended to be used for tracking the impact of free-time activities on
recovery, fatigue and sleep quality on a healthy subject. It is not a medical device and is not
intended to be used for diagnosis or monitoring of disease or other conditions, or investiga-
tion of a physiological process.
The product consists of electronic unit with attached bed sensor and a separate power
supply.
Intended use
Environmental conditions
Storage and transportation
• Temperature:
-
30°C -
+
50°C
• Relative humidity:
≤80%
Use
• Temperature:
+
10°C -
+
40°C
• Relative humidity:
≤75%
• Altitude:
<3000 m
Cleaning
CAUTION
Do not spray, pour or spill liquid onto the power supply, device, cables, or sensor.
The Emfit device may be surface-cleaned using a soft cloth dampened with either a commercial, nonabrasive cleaner or a
solution of 70% alcohol in water. Lightly wipe the surfaces of the device, power supply, cables and sensor.
EMFIT QS New device setup guide A2_v.3.0_28.5.2019.indd 1
5.6.2019 10.51
