background image

5

YarwaY

 SERiES 400 intEgRAl StRAinERimpulSE

®

InstructIon, operatIon and maIntenance manual

sErVICINg

After disassembly clean internal parts with 
a cloth and an on corrosive solvent. Heavy 
deposits may be cleaned from orifice in top 
of piston valve with a piece of fine wire or 
toothpick.
 
BE CAREFul not to damage valve orifice, disc 
edge or control cylinder bore (piston valve trap). 
under no circumstances should crocus cloth or 
tools be used to clean these parts.

inspect control cylinder bore, valve and seat 
for wear (discand seat in disc type trap). Worn 
parts cause inefficient or improper operation. 
they should be replaced with a factory set 
renewal kit. 

CautION

The valve, seat and control cylinder of the renewal 
kit are matched parts. They are not individually 
interchangeable with similar parts from other 
repair kits.

disc valve type

1.  Remove bonnet and unscrew seat.
2.  inspect and clean all parts. if satisfactory, 

reassemble trap. if internals require 
replacing, remove cap nut. then using 
wrench and screw driver simultaneously 
loosen adapter and locknut and unscrew 
adapter. See page 6 for repair kit 
installation and assembly.

parts lIst

Item

description

1

Body

2

Bonnet

3

Cap nut

4

Stud

5

nut

6*

Seat

7

Adapter

8*

Disc

10

locknut

12*

Cap gasket

13

Bonnet gasket

14

Seat gasket

15

Screen

steam trap 

Figure number

renewal kit 

part number

460 A
461 A

963559-01

460 B
461 B

963559-02

460 C
461 C

963559-03

* Renewal kit parts.

FiguRE 3
Disc valve type

FiguRE 4

FiguRE 5

Do not reuse any of the old parts when 
installing a new renewal kit. Always use new 
gaskets.
Repair kit of the disc type trap does not include 
bonnet and seat gasket. these should be 
ordered separately.
Clean the strainer screen with air or steam 
blast or wash in solvent.

sparE parts, spECIal tOOls

to cover a one year service period, it is 
recommended that spare parts be stocked as 
follows:
A.  One (1) repair kit for every four (4) integral 

strainer traps installed of same internals. 
(minimum number of kits -1) and sufficient 
gaskets for trap inspection.

For the disc valve type trap, the use of a 
spanner wrench (J. H. Williams #0-471A) is 
recommended for seat removal and tightening.

Содержание Yarway Integral Strainerimpulse 400 Series








Отзывы: