Emerson Yarway 7100 Series Скачать руководство пользователя

Страница: 44 / 60

NetSure

™

-48 VDC Power System

Installation Instructions, IM582127000100 (Revision A, January 9, 2017)

Spec. No: 582127000100, 582127000103

Document Code: IM582127000100

Model No: 7100

Revision A, January 9, 2017

[36]

Load Connections

Loads are connected to the various distribution panels located inside the distribution cabinet, as detailed in this section.

RECOMMENDED TORQUES

•

72 in-lbs for 1/4-inch hardware (when using standard flat and lock washer).

•

300 in-lbs for 3/8-inch hardware (when using standard flat and lock washer).

LOAD CONNECTIONS TO SINGLE VOLTAGE DISTRIBUTION PANELS

Figure 22.

List AL: -48 VDC Distribution Panel (with Return Busbar), (26) Bullet/TPS/TLS Circuit Breaker/Fuse Positions

LOAD CONNECTIONS TO DUAL VOLTAGE DISTRIBUTION PANELS

Figure 23.

List DJ: -48 VDC / +24 VDC Distribution Panel, (6) -48 VDC Bullet/TPS/TLS Circuit Breaker/Fuse Positions (with Return Busbar) and (20)

+24 VDC Bullet/TPS/TLS Circuit Breaker/Fuse Positions (with Return Busbar)

Observe proper

polarity when making

load connections.

WARNING!

-48 VDC Load

Connections

Load Return

Connections

LOAD AND LOAD RETURN CONNECTIONS

1/4-20 Studs on 5/8” Centers

(Customer must supply or order additional hardware)

Maximum Lug Width: 0.625 inches.

Return Busbar

Caution: A 100 A circuit breaker or fuse SHALL HAVE an empty mounting position

between it and any other overcurrent protective device. 100 A circuit breakers can

be used without a space provided the continuous current in each 100 A device

does not exceed 64 A. A 175 A or greater circuit breaker SHALL HAVE an empty

mounting position between it and any other overcurrent protective device.

Observe proper

polarity when making

load connections.

WARNING!

-48V

Distributio

+24V Distri

bution

LOAD AND LOAD RETURN CONNECTIONS

1/4-20 Studs on 5/8” Centers

(Customer must supply

or order additional

hardware)

Maximum Lug Width:

0.625 inches.

Load

Connections

Load Return

Connections

Caution: A 100 A circuit breaker or fuse SHALL HAVE an empty mounting position

between it and any other overcurrent protective device. 100 A circuit breakers can

be used without a space provided the continuous current in each 100 A device

does not exceed 64 A. A 175 A or greater circuit breaker SHALL HAVE an empty

mounting position between it and any other overcurrent protective device.

StockCheck.com

Содержание Yarway 7100 Series





























































Результаты поиска

Содержание Yarway 7100 Series

Отзывы:

Похожие инструкции для Yarway 7100 Series

Бренды по названию

Популярные бренды

Emerson Yarway 7100 Series, Руководство по установке

Результаты поиска

Содержание Yarway 7100 Series

Отзывы:

Похожие инструкции для Yarway 7100 Series

Бренды по названию

Популярные бренды