Emerson Yarway 7100 Series Скачать руководство пользователя страница 32

Страница: 32 / 60

NetSure

™

-48 VDC Power System

Installation Instructions, IM582127000100 (Revision A, January 9, 2017)

Spec. No: 582127000100, 582127000103

Document Code: IM582127000100

Model No: 7100

Revision A, January 9, 2017

[24]

SYSTEM INTERFACE BOARD

The System Interface Board provides connections for the following.
Refer to

Figure 17

•

Battery Tray or Battery Rack Fuse Alarm

•

System Voltage Monitoring Test Points

•

Temperature Probes (see “Temperature Probes” starting on page 23)

•

NCU CAN Port (see “Connecting a Device or System to the NCU CAN Bus (if required)” starting on page 34)

Figure 17.

System Interface Board Connections

System Interface Board

CAN termination plug

P/N 548398 must be

installed if an external

device is not connected

to the system.

TP1 (-) and TP2 (+)

System Voltage

J5 (System Temp 1)

NCU CAN Port

J6 (System Temp 2)

CR4

DS1

R10

R11

R12

R13

R15

TB1

562662

0 00 X X X X X

AX X X X X XX X

TB1 (Bat Tray FA,

Bat Rack FA)

StockCheck.com

Содержание Yarway 7100 Series





























































Результаты поиска

Содержание Yarway 7100 Series

Отзывы:

Emerson Yarway 7100 Series, Руководство по установке, Страница: 32 / 60

Результаты поиска

Содержание Yarway 7100 Series

Отзывы: