background image

valves.emerson.com

VCIOM-03189-EN 17/05

Before installation these instructions must be read fully and understood

© 2017 Emerson. All Rights Reserved.

VAREC 

SERiES 180/181 DouBlE poRt REgulAtoR

InstallatIon, operatIon and maIntenance InstructIons

LIMItAtIONs Of sELLER's LIAbILIty

in the event that a court holds that this 
instruction manual created some new 
warranties, the seller's liability shall be limited 
to repair or replacement under the standard 
warranty clause. in no case shall the seller's 
liability exceed that stated as limitations of 
Remedy in the contract between the seller and 
buyer.

use of parts that are not manufactured or 
supplied by Emerson voids any Emerson 
warranty and relieves Emerson of any 
obligation to service the product under 
warranty. Emerson recommends the use of 
only Emerson manufactured or supplied parts 
to maintain or service Varec Series 180/181 
double port regulators.

this document, or any part of, may not be 
reproduced by any means without written 
permission of Emerson.

DIsCLAIMER Of wARRANtIEs

the contract between the seller and the buyer 
states the entire obligation of the seller. the 
contents of this instruction manual shall not 
become part of or modify any prior or existing 
agreement, commitment or relationship 
between the seller and buyer. there are no 
express or implied warranties set out in this 
instruction manual. the only warranties that 
apply are those in the existing contract between 
the seller and buyer.

the Varec 180/181 Series double port 
regulators have not been tested under all 
possible operational conditions and Emerson 
does not have all the data relative to your 
application. the information in this instruction 
manual is not all inclusive and does not and 
cannot take into account all unique situations. 
Consequently, you should review this product 
literature in view of your application. if you have 
any further questions, please contact Emerson 
for assistance.

sAfEty pRECAutIONs

Read and understand this instruction manual 
before installing, operating or performing 
maintenance on Varec 180/181 series double port 
regulator. Follow all precautions and warnings 
noted herein when installing, operating or 
performing maintenance on this equipment.

safety precaution definitions:

CAutION

Damage to equipment may result if this 
precaution is disregarded.

wARNINg

Direct injury to personnel or damage to 
equipment which can cause injury to personnel 
may result if this precaution is not followed.

gENERAL

Varec Series 180/181 regulators are diaphragm 
operated and weighted lever controlled, highly 
sensitive gas control valves. the regulators 
are designed for maintaining a constant 
downstream pressure automatically. they are 
used widely in vapor recovery systems and gas 
blanketing systems to maintain a slight positive 
pressure on the tanks.

33-11023 Rev.D

Содержание VAREC Series

Страница 1: ...s or implied warranties set out in this instruction manual The only warranties that apply are those in the existing contract between the seller and buyer The Varec 180 181 Series double port regulators have not been tested under all possible operational conditions and Emerson does not have all the data relative to your application The information in this instruction manual is not all inclusive and...

Страница 2: ...e purposes Regulators having screwed connections should have all pipe lines fitted with ground joint unions located between the stop valves and the regulator Control line piping should be 2 size and should be connected to downstream piping as far downstream as possible preferably to the location at which the pressure control is desired Minimum should never be less than 10 feet from the regulator C...

Страница 3: ... to full open position of the regulator As the weights and arm are shifted toward the diaphragm side of the pivot clamp the setting is lowered 2 Major adjustments In the event it is not possible to attain the desired setting by the method described for minor adjustments it becomes necessary to make further adjustments by means of a spring provided for that purpose Prior to adjusting the spring it ...

Страница 4: ...tor can be checked by observing the system pressure when in operation Replacement parts When ordering replacement parts specify regulator parts by model number and pipe size Identify replacement parts by description and part number where possible Item description size 1 size 1 size 2 size 3 size 4 size 6 size 8 size Upper and lower body gasket B2194 046 B2194 046 B2194 046 B2194 046 B2244 046 B222...

Отзывы: