Emerson unidrive m Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 88

background image

50

SI-Safety Installation & Operating Manual

Issue Number: 1

7

Maintenance

7.1

Modification

Repair

This device can only be repaired by the original manufacturer.

Warranty

The warranty is void if the module is opened.

7.2

Module replacement

Note the following when replacing a module:
•

Disconnect the inverter from the line power supply.

•

Disconnect power supply from the device and remove the connection.

•

Remove the sensor connector.

•

Remove all other plug type connections.

•

Remove module from top hat rail and package in an EMC compliant manner.

•

Install a new module to the top hat rail.

•

Remake all connections.

•

Switch on the inverter.

•

Switch on the power supply.

•

Configure the device.

7.3

Maintenance intervals

Table 7-1

7.4

Diagnostic parameters

The SI-Safety module is designed to accept predefined data during operation. A fully
assigned patch cable for connecting the SI-Safety module (RJ45) and the Unidrive M
(RJ45) is required. The data to be transferred are defined in

CTSafePro

. The

configuration of the signal channel data is defined as shown in Table 7-1.

The safety approval is void if the module is modified.

WARNING

Under no circumstances should any plug type connection on the SI-Safety module be
disconnected or reconnected while power is applied to the device, as there is a risk of
failure or permanent destruction of the connected position and/or speed sensors.

CAUTION

Module replacement

See Technical Data Section 2-2

Key technical

Function test

See ‘Start-up’ chapter

«
...
48
49
50
51
52
...
»

Содержание unidrive m

























































































Отзывы:

Нет отзывов

Похожие инструкции для unidrive m

Leroy-Somer R180

Бренд: Nidec Страницы: 20

Бренд: C&K systems Страницы: 2

Бренд: E-fly Страницы: 16

Бренд: Salda Страницы: 16

Бренд: Watlow Страницы: 4

Бренд: York Страницы: 24

SMARTSTART 6000

Бренд: Zener Страницы: 36

Бренд: Zapi Страницы: 5

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренд: Eaton Страницы: 8

Бренд: ABB Страницы: 44

Бренд: Omega Страницы: 2

Бренд: Zmotion Страницы: 34

Бренд: +GF+ Страницы: 3

Бренд: Össur Страницы: 58

Бренд: Vizio Страницы: 65

Бренд: Coris Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды