Emerson Unidrive HS72 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 46

background image

Unidrive M702 / HS72 Control Getting Started Guide

19

Issue Number: 2

Safety inform

Introdu

C

Basic p

Runn

F

4.7

Changing the operating mode

Changing the operating mode returns all parameters to their default value, including the motor
parameters.

User security status

(00.049) and

User security code

(00.034) are not affected by this

procedure).

Procedure

Use the following procedure only if a different operating mode is required:
1. Ensure the drive is not enabled, i.e. terminals 11 and 13 are open or Pr

06.015

is Off (0)

2. Enter either of the following values in Pr

mm.000

, as appropriate:

1253 (50 Hz AC supply frequency)
1254 (60 Hz AC supply frequency)

3. Change the setting of Pr

00.048

as follows:

The figures in the second column apply when serial communications are used.
4. Either:
•

Press the red

reset button

•

Toggle the reset digital input

•

Carry out a drive reset through serial communications by setting Pr

10.038

to 100.

4.8

Saving parameters

When changing a parameter in Menu 0, the new value is saved when pressing the

Enter

button to return to parameter view mode from parameter edit mode.
If parameters have been changed in the advanced menus, then the change will not be saved
automatically. A save function must be carried out.

Procedure

1. Select ‘Save Parameters'* in Pr

mm.000

(alternatively enter a value of 1000* in Pr

mm.000

)

2. Either:
•

Press the red

reset button

•

Toggle the reset digital input, or

•

Carry out a drive reset through serial communications by setting Pr

10.038

to 100

* If the drive is in the under voltage state (i.e. when the control terminal 9 and 10 are being supplied
from a low voltage DC supply) a value of 1001 must be entered into Pr

mm.000

to perform a save

function.

Pr 00.048 setting

Operating mode

1

Open-loop

(Induction motor)

2

RFC-A

(Induction motor with position feedback)

3

RFC-S

(Permanent magnet motor with position feedback)

Entering 1253 or 1254 in Pr

mm.000

will only load defaults if the setting of Pr

00.048

has

been changed.

NOTE

Unidrive M702_HS72 Control GSG Iss2.book Page 19 Friday, December 12, 2014 1:05 PM

«
...
17
18
19
20
21
...
»

Содержание Unidrive HS72















































Отзывы:

Нет отзывов

Похожие инструкции для Unidrive HS72

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Бренд: Radio Shack Страницы: 52

Бренд: GE Страницы: 425

Бренд: 1Control Страницы: 8

Бренд: Yudian Страницы: 26

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: V2 ELETTRONICA Страницы: 6

Бренд: Hach Страницы: 210

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Harsco Industrial Страницы: 57

Бренд: Maestra Страницы: 22

Бренд: Samson Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды