Emerson SolaHD SPD50K Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 20

Emerson SolaHD SPD50K Series Скачать руководство пользователя страница 11

Page: 9

SPD50K

NOTICE

INADEQUATE RACEWAY ELECTRICAL CONTINUITY

•

Install an insulated grounding conductor inside a metallic raceway

when the raceway is used as an additional

grounding conductor. Size the conductor in accordance with all applicable codes.

• Maintain adequate electrical continuity at all raceway connections.
•

Do not use isolating bushings to interrupt a metallic raceway run.

•

Do not use a separate isolated ground for the surge protective device.

•

Verify proper equipment connections to the grounding system.

•

Verify ground grid continuity by inspections and testing as part of a comprehensive electrical maintenance

program.

Failure to follow these instructions can result in equipment damage.

Wiring and Installation

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E,

NOM-029-STPS or CSA Z462.

•

This equipment must only be installed and serviced by qualified electrical personnel.

•

Turn off all power supplying this equipment before working on or inside equipment.

•

Always use a properly rated voltage sensing device to confirm power is off.

•

Replace all devices, doors and covers before turning on power to this equipment.

•

This equipment must be effectively grounded per all applicable codes. Use an equipment-grounding conductor to

connect this equipment to the power system ground.

•

Confirm the surge protective device voltage rating on the module or nameplate label is not less than the operat

-

ing voltage.

Failure to follow these instructions will result in death or serious injury.

Parts List

1 - SPD50K suppressor including 3' (~1m) conductors
1 - 3/4” conduit nut
1 - L bracket mounting kit; includes two pan head screws
1 - Instructions

«
...
9
10
11
12
13
...
»

Содержание SolaHD SPD50K Series





















Отзывы:

Нет отзывов