Emerson Rosemount Xi Скачать руководство пользователя страница 69

Страница: 69 / 82

Figure 6-7: Power supply board wiring

A. From DR board for Traditional Architecture configurations

B. Power Supply Board

4. Disconnect the 14-pin ribbon cable from the power supply board.
5. Remove the two long screws that secure the bracket (9,

Figure 6-1

) to the

Rosemount Xi enclosure.

6. Hold the AC input wiring to the right and slide the power supply board out of the

Rosemount Xi enclosure.

7. Install the new mounting bracket (9,

Figure 6-1

) on the new power supply board

(10,

Figure 6-1

A new bracket and mounting screws are provided in the replacement kit.

8. Slide the power supply board into the mating slots in the Rosemount Xi enclosure.

Make sure the board is correctly aligned in the slots.

9. Install and tighten the bracket mounting screws.

Two new screws are provided in the replacement kit and should be used if the
existing screws are damaged.

10. Connect the ribbon cable to the power supply board.

A new ribbon cable (7,

Figure 6-1

) is provided in the replacement kit and should be

used if the existing cable is damaged.

11. Connect the AC power plug to the power supply board.
12. Swing the Rosemount Xi cover up and tighten the four mounting screws.

Reference Manual

Maintenance and service

00809-0100-4889

October 2022

Emerson.com/Rosemount

Содержание Rosemount Xi



















































































Результаты поиска

Содержание Rosemount Xi

Отзывы:

Похожие инструкции для Rosemount Xi

Бренды по названию

Популярные бренды

Emerson Rosemount Xi, Справочное руководство

Результаты поиска

Содержание Rosemount Xi

Отзывы:

Похожие инструкции для Rosemount Xi

Бренды по названию

Популярные бренды