Emerson Rosemount Smart Wireless THUM Скачать руководство пользователя | Manualshive

Страница: 9 / 60

background image

Reference Manual

00809-0100-4075, Rev BA
October 2010

1-3

Smart Wireless THUM Adapter

CONSIDERATIONS

General

The Smart Wireless THUM Adapter is connected to a HART sub-device. With
simple HART configuration, the THUM transmits the HART information from
the sub-device into the Wireless network.

Commissioning

The THUM can be commissioned before or after installation. It may be useful
to bench commission the THUM before installation to ensure proper operation
and to become familiar with the functionality. The instruments should be
installed in accordance with intrinsically safe or non-incendive field wiring
practices, when required. The THUM Adapter is powered when connected to
a powered loop.

Mechanical

When choosing an installation location and position for the transmitter, take
into account access to the device. For best performance, the antenna should
be vertical and have some space between objects in a parallel metal plane
such as a pipe or metal framework, as the pipes or framework may adversely
affect the performance of the antenna.

Electrical

The THUM Adapter is connected into a powered 4–20 mA loop, powering
itself by scavenging power. The THUM Adapter causes a voltage drop across
the loop. The drop is linear from 2.25 volts at 3.5 mA to 1.2 volts at 25 mA, but
does not effect the 4–20 mA signal on the loop. Under fault conditions, the
maximum voltage drop is 2.5 volts.

Environmental

Verify that the operating environment of the transmitter is consistent with the
appropriate hazardous locations certifications.

Temperature Limits

Wireless Considerations

Power Up Sequence

Power should not be applied to any wireless device until the Smart Wireless
Gateway (“Gateway”) is installed and functioning properly. Wireless devices
should also be powered up in order of proximity from the Gateway, beginning
with the closest. This will result in a simpler and faster network installation.
Enable Active Advertising on the Gateway to ensure that new devices join the
network faster. For more information see the Smart Wireless Gateway Manual
(Doc. No. 00809-0200-4420).

THUM Adapter Position

If possible, the THUM Adapter should be positioned vertically, either straight
up or straight down, and it should be approximately 3 ft. (1 m) from any large
structure, building, or conductive surface to allow for clear communication to
other devices. If the THUM Adapter is mounted horizontally, wireless
communication range may be decreased.

Operating Limit

Storage Limit

–40 to 185 °F
–40 to 85 °C

–40 to 185 °F
–40 to 85 °C

«
...
7
8
9
10
11
...
»

Содержание Rosemount Smart Wireless THUM





























































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Smart Wireless THUM

Бренд: Targus Страницы: 10

miniSD SCHF Series

Бренд: Alps Electric Страницы: 2

Thunderbolt RocketStor 6324U

Бренд: HighPoint Страницы: 10

Powerline Adaptor Kit

Бренд: NETGEAR Страницы: 8

10/100/1000 Base-T Ethernet PCI

Бренд: IBM Страницы: 38

Бренд: Allen-Bradley Страницы: 2

Бренд: Tripp Lite Страницы: 25

Бренд: StarTech.com Страницы: 10

VERDEdri 17-10504K

Бренд: World Dryer Страницы: 8

FM 5 IN DASH ADAPTER KIT

Бренд: Eagle Страницы: 5

WorkForce 600 Series

Бренд: Epson Страницы: 2

Бренд: JVC Страницы: 6

Бренд: JVC Страницы: 11

Бренд: JVC Страницы: 4

Бренд: JVC Страницы: 18

Бренд: JVC Страницы: 4

Бренд: JVC Страницы: 24

Бренд: JVC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды