Emerson Rosemount Smart Wireless THUM Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 60

background image

Reference Manual

00809-0100-4075, Rev BA
October 2010

6-1

Smart Wireless THUM Adapter

Section 6

Troubleshooting

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6-1
Troubleshooting Recommended Actions . . . . . . . . . . . . . page 6-2

OVERVIEW

Table 6-1 on page 6-2 provides summarized maintenance and
troubleshooting suggestions for the most common operating problems.

If you suspect malfunction despite the absence of any diagnostic messages
on the Field Communicator display, follow the procedures described here to
verify that transmitter hardware and process connections are in good working
order. Always deal with the most likely checkpoints first.

Warnings

Failure to follow these installation guidelines could result in death or serious injury

:

•

Only qualified personnel should perform the installation

Explosions could result in death or serious injury.

•

Before connecting a Field Communicator in an explosive atmosphere, make
sure that the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices

•

Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications

Electrical shock could cause death or serious injury.

•

Use extreme caution when making contact with the leads and terminals

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following conditions: This device may not cause harmful interference. This device must
accept any interference received, including interference that may cause undesired
operation.

This device must be installed to ensure a minimum antenna separation distance of 20
cm from all persons.

«
...
41
42
43
44
45
...
»

Содержание Rosemount Smart Wireless THUM





























































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Smart Wireless THUM

Бренд: Dynex Страницы: 48

WUSB11 ver. 2.6

Бренд: Linksys Страницы: 10

Бренд: Belkin Страницы: 18

LUXOMAT IR-RC-Adapter

Бренд: B.E.G. Страницы: 4

Бренд: RocketFish Страницы: 16

Бренд: Avaya Страницы: 2

Бренд: Tanita Страницы: 16

Бренд: Lenze Страницы: 6

Бренд: Arion Страницы: 18

LINKSYS WMP300N

Бренд: Linksys Страницы: 71

Бренд: Intermec Страницы: 174

Бренд: Asus Страницы: 21

Бренд: Asus Страницы: 2

Бренд: Asus Страницы: 48

Бренд: Asus Страницы: 2

Бренд: Asus Страницы: 4

Бренд: Asus Страницы: 13

USB-BT211 Mini Bluetooth Dongle

Бренд: Asus Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды