Emerson Rosemount CT5100 Скачать руководство пользователя страница 116

Страница: 116 / 179

11.2

Faults menu

The

Faults

menu displays a list of faults affecting the analyzer that have been identified by

the BIST.

If no faults have been identified by the BIST the central area of the

Faults

menu will display

No FAULTS

(see

Figure 11-5

Figure 11-5: Faults Menu - No Faults Indicated

Procedure

1. Press the

REFR

button to refresh the fault list (B).

Refer to

Figure 11-6

2. Use the

Scroll Up

(D) and

Scroll Down

(G) buttons to highlight a fault for further

investigation by the BIT system.

3. Once the fault that you wish to diagnose has been highlighted, press the

SEL

button

to select that fault.
The

Fault Display

screen for the component that is reporting an error will then open.

The

Fault Display

screen will display the parameters of the suspect component.

Figure 11-7

shows an example of a Fault Display; the precise data that will be

displayed will vary depending upon where the fault has occurred.

Troubleshooting and diagnostics

Reference Manual

October 2019

00809-0100-4512

116

Rosemount CT5100(Ex)

Содержание Rosemount CT5100




















































































































































































Результаты поиска

Содержание Rosemount CT5100

Отзывы:

Похожие инструкции для Rosemount CT5100

Бренды по названию

Популярные бренды

Emerson Rosemount CT5100, Справочное руководство

Результаты поиска

Содержание Rosemount CT5100

Отзывы:

Похожие инструкции для Rosemount CT5100

Бренды по названию

Популярные бренды