Emerson ROSEMOUNT Analytical SPS 4000 B201110 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 42

background image

Instruction Manual

IB-106-340AC Rev. 1.3

January 2003

Rosemount Analytical Inc. A Division of Emerson Process Management

Operation 3-1

SPS 4000

SECTION 3

OPERATION

3-1 OVERVIEW

This section specifies the requirements to set up
an Oxymitter 4000 calibration and how to verify
the calibration gas flow setup. It also explains
the differences between automatic and semi-
automatic calibrations and how to initiate them.

3-2 CALIBRATION

REQUIREMENTS

a.

Two tanks of precision calibration gas mix-
tures are required. Recommended calibra-
tion gases are nominally 0.4% and 8.0%
oxygen in nitrogen.

Do not use 100% nitrogen as a low gas
(zero gas). It is suggested that gas for
the low (zero) be between 0.4% and
2.0% O2. Do not use gases with hy-
drocarbon concentrations of more
than 40 parts per million. Failure to
use proper gases will result in errone-
ous readings.

In addition to the optional disposable gas
bottles available from Rosemount, two ad-
ditional sources of calibrated gas mixtures
are:

LIQUID CARBONIC GAS CORP.
SPECIALTY GAS LABORATORIES

700 South Alameda Street
Los Angeles, California 90058
213/585-2154

767 Industrial Road
San Carlos, California 94070
415/592-7303

9950 Chemical Road
Pasadena, Texas 77507
713/474-4141

12054 S.W. Doty Avenue
Chicago, Illinois 60628
312/568-8840

603 Bergen Street
Harrison, New Jersey 07029
201/485-1995

255 Brimley Road
Scarborough, Ontario, Canada
416/266-3161

SCOTT ENVIRONMENTAL
TECHNOLOGY, INC.
SCOTT SPECIALTY GASES

2600 Cajon Blvd.
San Bernardino, California 92411
714/887-2571
TWX: 910-390-1159

1290 Combermere Street
Troy, Michigan 48084
314/589-2950

Route 611
Plumsteadville, Pennsylvania 18949
215/766-8861
TWX: 510-665-9344

2616 South Loop West
Suite 100
Houston, Texas 77054
713/669-0469

b.

A check valve is required at the Oxymitter
4000 (between the calibration fitting and the
gas line) to prevent the migration of process
gases down the calibration gas line.

A typical calibration setup for the Oxymitter
4000 is shown in Figure 1-4.

3

«
...
19
20
21
22
23
...
»

Содержание ROSEMOUNT Analytical SPS 4000 B201110











































Отзывы:

Нет отзывов

Похожие инструкции для ROSEMOUNT Analytical SPS 4000 B201110

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: GE Страницы: 24

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

Бренд: Halyard Страницы: 88

Бренд: HALDER Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: laerdal Страницы: 9

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

Бренд: Aspect Medical Systems Страницы: 104

Бренд: Garmat Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды