Emerson Rosemount 975HR Скачать руководство пользователя страница 44

Страница: 44 / 80

•

Only access the wiring compartment to wire or remove the detector or access RS-485
terminals for maintenance.

•

Disconnect or disable external devices, such as automatic extinguishing systems,
before carrying out any maintenance.

3.2.1

Factory default function settings

Table 3-1

lists the default function configurations supplied with the detector.

Table 3-1: Factory Default Function Settings

Function

Value

Notes

Sensitivity

Alarm delay

Antiflare

Alarm latch

Auxiliary relay

In output configurations 1A,
2A, and 3A, the auxiliary relay is
not available. This function is
not used.

Automatic built-in test (BIT)

Yes

Alarm built-in-test

Auxiliary built-in test

In output configurations 1A,
2A, and 3A, the auxiliary relay is
not available. This function is
not used.

Heated optics

Auto

Heat on

41 °F (5 °C)

The detector starts heating the
window for any temperature
below this value.

In order to change the default function, use:

•

USB RS-485 harness kit PN 00975-9000-001

•

HART

protocol. Refer to the

Rosemount 975 Flame Detector HART Communication

Manual (00809-0200-4975)

for instructions.

3.3

Testing procedures

This section describes the proof testing procedure for proper operation of the detector.
Test the detector using the manual built-in test (BIT) or the flame simulator.

The detector performs the internal test continuously and the automatic built-in test every
fifteen minutes; for more details, refer to

Built-in test (BIT)

Operating the detector

Reference Manual

June 2021

00809-0100-4976

Emerson.com/Rosemount

Legacy

Содержание Rosemount 975HR

















































































Результаты поиска

Содержание Rosemount 975HR

Отзывы:

Похожие инструкции для Rosemount 975HR

Бренды по названию

Популярные бренды

Emerson Rosemount 975HR, Справочное руководство

Результаты поиска

Содержание Rosemount 975HR

Отзывы:

Похожие инструкции для Rosemount 975HR

Бренды по названию

Популярные бренды