Emerson Rosemount 8800D Series Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 192

background image

53

Reference Manual

00809-0100-4772, Rev FA

Transducer Block

March 2016

Transducer Block

4.2.2

Diagnostics

In addition to the BLOCK_ERR and XD_ERROR parameters, more detailed information on
the measurement status can be obtained through the TB_ELECTRONICS_STATUS.

lists the potential errors and the possible corrective actions for the given values.

Table 4-3. XD_ERR Conditions

Condition

number

Condition name and description

15

Out of Service: The actual mode is out of service.

16

Unspecified error: An unidentified error occurred.

17

General Error: A general error that cannot be specified below

occurred.

18

Calibration Error: An error occurred during calibration of the device,

or a calibration error was detected during normal operations.

19

Configuration Error: An error occurred during configuration of the

device, or a configuration error was detected during normal

operations.

20

Electronics Failure: An electrical component failed.

21

Mechanical Failure: A mechanical component failed.

22

I/O Failure: An I/O failure occurred.

23

Data Integrity Error: Data stored in the device are no longer valid

due to a nonvolatile memory checksum failure, a data verify after

write failure, etc.

24

Software Error: The software has detected an error due to an

improper interrupt service routine, an arithmetic overflow, a

watchdog time-out, etc.

25

Algorithm Error: The algorithm used in the transducer block

produced an error due to overflow, data reasonableness failure, etc.

Table 4-4. Transducer Block Status Definitions (TB_ELECTRONICS_STATUS)

Value

Name and description

LCD display
indication
(if any)

Corrective actions

0x00000002

SW_DETECTED_ERR: The device software has detected

a software (typically math) error.

FAULT SFTWR

Restart the transmitter.

(1)

0x00000004

COPROCESSOR_ERR: The coprocessor has detected a

math or instruction error.

FAULT COPRO

Restart the transmitter.

0x00000010

INTERRUPT_ERROR: The transducer block has detected

that the coprocessor ASIC has stopped generating flow

data interrupts.

FAULT ASIC

Restart the transmitter.

0x00000020

COPROC_RAM_ERR: The coprocessor has detected a

RAM error at startup.

FAULT RAM

Restart the transmitter.

0x00000040

COPROC_ROM_ERR: The coprocessor has detected a

ROM error at startup.

FAULT ROM

Restart the transmitter.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

«
...
61
62
63
64
65
...
»

Содержание Rosemount 8800D Series

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 8800D Series

Бренд: Vega Страницы: 28

Бренд: Vega Страницы: 20

Бренд: Hanna Instruments Страницы: 2

Бренд: Yamaha Страницы: 8

Бренд: Teledyne Lecroy Страницы: 4

Бренд: Van Walt Страницы: 2

Ratio:Guard Advanced

Бренд: H.E. Anderson Страницы: 9

Бренд: SEFRAM Страницы: 31

Бренд: Ocean Reef Страницы: 24

FI-500 FiberInspector Micro

Бренд: Fluke Страницы: 2

Бренд: IMI Hydronic Страницы: 48

Бренд: Fluke Страницы: 97

Бренд: Delmhorst Страницы: 9

Бренд: Micronics Страницы: 36

Бренд: Teledyne Страницы: 79

Бренд: Eddyfi Technologies Страницы: 31

Бренд: Vanguard Instruments Company Страницы: 44

Бренд: Ada Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды