Emerson Rosemount 705 Скачать руководство пользователя страница 18

Страница: 18 / 70

Reference Manual

00809-0200-4705, Rev AB

Mounting

May 2017

Mounting

Figure 3-4. Antenna Positioning

3.2.2

Installing the transmitter in a remote mount configuration

Figure 3-5. Remote Mount Installation

A. Turbine meter
B. Rosemount 705 Transmitter
C. 1-in. supplied cable gland adapter for turbine meter.

Included:
(1) Cable gland
(1) Cable gland adapter for turbine meter
10 ft.. of cable connection wiring

1. Install the turbine meter or pulse output device according to standard installation practices being

sure to use thread sealant on all of the connections.

2. Pull the cable connection wiring through the supplied cable gland adapter for the turbine meter.

Then pull the cable wiring through the transmitter cable gland.

Note

Pay attention to the orientation of the cable gland to ensure proper connection to transmitter.

3. Attach the turbine meter or pulse output device wiring to the terminals as shown in the wiring

diagrams beginning on

page 8

Note

Wireless devices should only be powered up after the Smart Wireless Gateway, in order of proximity from
the Gateway beginning with the closest device. This results in a simpler and faster network installation.

Possible antenna rotation shown.
Antenna rotation allows for best
installation practices in any
configuration.

Содержание Rosemount 705







































































Результаты поиска

Содержание Rosemount 705

Отзывы:

Похожие инструкции для Rosemount 705

Бренды по названию

Популярные бренды

Emerson Rosemount 705, Справочное руководство

Результаты поиска

Содержание Rosemount 705

Отзывы:

Похожие инструкции для Rosemount 705

Бренды по названию

Популярные бренды