manualshive.com logo in svg

Emerson Rosemount 644 FOUNDATION, Справочное руководство

Поделиться
Скачать
Emerson Rosemount 644 FOUNDATION Скачать руководство пользователя страница 8

2

Reference Manual

00809-0400-4728, Rev CA

Introduction

September 2018

Introduction

1.2.3

Mechanical

Location

When choosing an installation location and position, take into account the need for access to the 
transmitter.

Special mounting

Special mounting hardware is available for mounting a Rosemount 644 head mount transmitter to a DIN 
rail or assembling a new Rosemount 644 head mount to an existing threaded sensor connection head 
(former option code L1).

1.2.4

Electrical 

Proper electrical installation is necessary to prevent errors due to sensor lead resistance and electrical 
noise. For best results, shielded cable should be used in electrically noisy environments. 

Make wiring connections through the cable entry in the side of the connection head. Be sure to provide 
adequate clearance for cover removal.

1.2.5

Environmental

The transmitter electronics module is permanently sealed within the housing, resisting moisture and 
corrosive damage. Verify that the operating atmosphere of the transmitter is consistent with the 
appropriate hazardous locations certifications.

Temperature effects 

The transmitter will operate within specifications for ambient temperatures between –40 and 185 °F 
(–40 and 85 °C). Heat from the process is transferred from the thermowell to the transmitter housing. If 
the expected process temperature is near or beyond specification limits, consider the use of additional 
thermowell lagging, and extension nipple, or a remote mounting configuration to isolate the transmitter 
from the process. 

Figure 1-1

 provides an example of the relationship between transmitter housing temperature rise and 

extension length. 

Figure 1-1. Rosemount 644 Head Mount Transmitter Connection Head Temperature Rise vs. 

Extension Length

H

o

u

sin

g

 te

m

p

e

rat

u

re

 r

ise

, ab

ove

 a

m

bi

e

n

t °

C

 (

°F

)

3

4

5

6

7

8

9

0

60 (108)

50 (90)

40 (72)

30 (54)

20 (36)

10 (18)

3.6

22

Extension length (in.)

815 °C (1500 °F) oven temperature

540 °C (1000 °F) 
oven temperature

250 °C (482 °F) oven temperature

Содержание Rosemount 644 FOUNDATION

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды