manualshive.com logo in svg

Emerson Rosemount 644 FOUNDATION, Справочное руководство

Поделиться
Скачать
Emerson Rosemount 644 FOUNDATION Скачать руководство пользователя страница 35

29

Reference Manual 

00809-0400-4728, Rev CA

Installation

September 2018

Installation

Section 3

Installation

Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 29
Safety messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 29
Mounting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 31
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 32
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 35
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 38

3.1

Overview

The information in this section covers installation considerations for the Rosemount

™

 644 Temperature 

Transmitter with F

OUNDATION

 Fieldbus

™

 Protocol. A Quick Start Guide is shipped with every transmitter to 

describe recommended mounting and wiring procedures for initial installation. Dimensional drawings 
for Rosemount 644 Transmitter mounting configurations are included in the 

Product Data Sheet

.

3.2

Safety messages

Instructions and procedures in this section may require special precautions to ensure the safety of the 
personnel performing the operations. Information that potentially raises safety issues is indicated by a 
warning symbol ( ). Please refer to the following safety messages before performing an operation 
preceded by this symbol.

Failure to follow these installation guidelines could result in death or serious injury.

 

Make sure only qualified personnel perform the installation.

Explosions could result in death or serious injury. 

Do not remove the connection head cover in explosive atmospheres when the circuit is live.

Before connecting a Field Communicator in an explosive atmosphere, make sure the instruments in 
the loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.

Verify that the operating atmosphere of the transmitter is consistent with the appropriate hazardous 
locations certifications.

All connection head covers must be fully engaged to meet explosion-proof requirements.

Process leaks could result in death or serious injury. 

Do not remove the thermowell while in operation.

Install and tighten thermowells and sensors before applying pressure.

Electrical shock could cause death or serious injury. 

Use extreme caution when making contact with the leads and terminals.

Содержание Rosemount 644 FOUNDATION

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды