Emerson Rosemount 5900S Series Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 298

Emerson Rosemount 5900S Series Скачать руководство пользователя страница 96

4.2

Overview

The Rosemount

™

5900S can be installed in Rosemount Tank Gauging systems including

Rosemount 2460 System Hubs and Rosemount 2410 Tank Hubs. The Rosemount 5900S
also supports installation in F

OUNDATION

™

Fieldbus systems. See

System overview

information.

Installation of the Rosemount 5900S is a simple and straight-forward procedure. In a
Rosemount Tank Gauging system with Rosemount 2410 Tank Hub and Rosemount 2460
System Hub it basically includes the following steps:

1. Preparations: make a note of Unit ID, Modbus address

, antenna type, tank

geometry parameters such as tank height, tank type, strapping table.

2. Set up communication protocol and communication parameters.

3. Configuration of the Rosemount 2460 System Hub.

4. Configuration of the Rosemount 2410 Tank Hub.

5. Configuration of field devices such as the Rosemount 5900S Radar Level Gauge and

the Rosemount 2240S Multiple-Input Temperature Transmitter.

6. Calibration of the Rosemount 5900S.

Installation of the Rosemount 5900S in F

OUNDATION

Fieldbus systems is supported by a

complete set of Resource, Function, and Transducer blocks. You can easily integrate the
level gauge into any existing F

OUNDATION

Fieldbus network by using an appropriate

configuration tool such as the AMS Device Manager. See section

for more information.

The Rosemount

™

TankMaster

™

WinSetup program is the recommended tool for

installation and configuration of a Rosemount 5900S Radar Level Gauge in systems that
include a Rosemount 2410 Tank Hub. The Rosemount 5900S is preferably installed as part
of the procedure when installing a tank hub:

1. Install and configure the Rosemount 2410 Tank Hub by using the device installation

wizard in TankMaster WinSetup.

2. Ensure that automatic installation of field devices is enabled when finishing the tank

hub installation. The Rosemount 2410 Tank Hub, Rosemount 5900S Level Gauge,
and other field devices on the Tankbus will automatically appear in the WinSetup
workspace.

3. Configure the Rosemount 5900S level gauge via the

Properties

window.

If a Rosemount 5900S level gauge is added to an existing system, the tank hub’s database
must be updated before the level gauge is configured. The tank database maps the level
gauge to the tank on which it is installed.

A detailed description of how to install and configure a Rosemount 5900S and other
devices by using the Rosemount TankMaster WinSetup software is provided in the
Rosemount Tank Gauging

System Configuration Manual

.

(9)

See the Rosemount Tank Gauging

System Configuration Manual

.

Configuration

Reference Manual

September 2019

00809-0100-5900

96

Reference Manual

«
...
94
95
96
97
98
...
»

Содержание Rosemount 5900S Series











































































































































































































































































































Отзывы:

Нет отзывов