Emerson Rosemount 5900S Series страница 116 Скачать руководство пользователя | Manualshive

Страница: 116 / 298

background image

4.6

LPG configuration

4.6.1

Preparations

Prerequisites

Before starting configuration of the Rosemount

™

5900S for LPG measurements, ensure

that all mechanical installations are made according to instructions, and all external
sensors such as pressure and temperature sensors are properly connected.

For Rosemount 5900S with F

OUNDATION

™

Fieldbus the LPG Setup is described in

using DeltaV / AMS Device Manager

Highly pressurized vapor above the product surface affects the propagation speed of
microwaves. The Rosemount 5900S level gauge is able to compensate for this, thus
avoiding deviations in measured level due to the vapor.

When the gauge is installed on the empty tank, calibrate the gauge and configure for LPG
measurements.

To install a Rosemount 5900S for LPG measurements perform the following major steps:

Procedure

1. Install the tank and the Rosemount 5900S level gauge in Rosemount TankMaster

WinSetup as described in the Rosemount Tank Gauging

System Configuration

. Ensure that the appropriate tank and device types are selected, and the

temperature and pressure sensors are properly configured. Check that the gauge
communicates with the TankMaster PC.

2. Install the Rosemount 5900S gauge on the still-pipe. Measure the exact distance to

the Verification Pin.

3. Configure the Rosemount 5900S according to the standard procedure for a

Rosemount 5900S level gauge (see the Rosemount Tank Gauging

Configuration Manual

). Rosemount TankMaster Winsetup is the recommended

configuration tool.

4. Configure the vapor pressure sensor.
5. Set Correction Method to Air Correction Only.
6. Calibrate the Rosemount 5900S.
7. Configure the Verification Pin.
8. Verify position of Verification Pin.
9. Set up the Correction Method that applies to the particular type of product in the

tank.

The LPG installation procedure using Rosemount TankMaster Winsetup is described
in section

LPG setup using Rosemount

.

Configuration

Reference Manual

September 2019

00809-0100-5900

116

Reference Manual

«
...
114
115
116
117
118
...
»

Содержание Rosemount 5900S Series











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 5900S Series

Бренд: MALA Страницы: 16

Бренд: Hama Страницы: 16

Бренд: Applied Satellite Engineering Страницы: 6

Бренд: Channel Master Страницы: 7

Бренд: Outbacker Страницы: 3

Traveller-Man 3

Бренд: Megasat Страницы: 68

Бренд: Hughes Network Systems Страницы: 27

Бренд: ETS-Lindgren Страницы: 13

Бренд: SELFSAT Страницы: 50

Blitz BZ2000-ANT

Бренд: Ikan Страницы: 10

Бренд: RCA Страницы: 12

Бренд: Shively Labs Страницы: 64

Бренд: iBeam Страницы: 2

Rayzar.Air RVRZ25B

Бренд: Winegard Страницы: 12

Бренд: Simrad Страницы: 5

SWA4U ANTENNA DIVIDER

Бренд: SABINE Страницы: 7

Бренд: Clas Ohlson Страницы: 5

Бренд: Label Italy Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды